When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hello
since i could not post a ticket (got the message 'could not create a ticket'), I try it again with almost no text here but added the content in a txt-file.
Hope...
Dear Nordic-Team,
we are currently trying to add CSR creation to our project which worked quite fine by implementing it similar to the psa_crypto sample.
Unfortunately...
Hello Nordic Team, We are developing a wearable health device using the nRF5340-DK and Zephyr RTOS. As part of the BLE communication design, we intend to use **Security Level...
I am looking at options to integrate the ADXL 367 accelerometer into my firmware project (nRF Connect SDK 3.0.2). I see the sensor is supported by Zephyr and has a complex...
We are hardware manufacturing company currently developing AMI solutions with Wirepas integration. Do any of your partners offer smart meter solutions that use Wirepas and...
Before i inserted in my code to use ppi + gpiote + spim usb serial device port worked properly, it connected normally, but now it doesn't connect the port at all, did i create...
Hello, I am working on a custom board with my own custom project/application. I have recently done porting from ncs v2.7.0 to v3.0.2 - I was able to initialise the wifi driver...
Hi Nordic team,
I'm currently working on a real-time distance measurement project using channel sounding with the nRF54L15 DKs. I’ve been using the channel_sounding_ras_initiator...
Dear Team,
I would like to know if it is possible to add custom attributes and commands to standard clusters, such as the Occupancy cluster. I have reviewed the "Adding...
Hi everyone—I'm working with the Nordic nRF54L15 SoC , but I'm struggling to find guidance on using a chip antenna (design and components) . The official materials (e.g.,...
Hi Team,
I’m facing an issue when trying to perform BLE FOTA with a 2 MB external SPI flash (SPI4) as the secondary slot for MCUboot.
My setup works fine when using a...
Hello,
sorry, do not know where to file a bug.
Bug is, that nrf_radio_subscribe_get() and nrf_radio_publish_get() use the wrong offset (0x80) instead of the correct one...
Hi, I’m currently testing the update process via BT SMP on the matter window covering example (NCS 3.0.2, nrf5340). For my test, I created two versions: 1. Project with -DCONFIG_CHIP_DFU_OVER_BT_SMP...
Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
