Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hello,
I have a BLE DFU question in this thread that has not yet been resolved.
Since the BLE DFU problem has not been resolved, I have implemented a USB DFU as an alternative...
Hi, I bougth 2 nrf52840 dongle but I dont't know how to use it or program them. So I tried to learn about it looking the getting started guide, this beginners tutorial and...
Hi All,
I have a few nRF9151 that don't want to boot.
I'm not sure if they ever had working modem firmware on them:
Any ideas on how to un-brick?
Thanks!
Ja...
HI,
I am using "NRF_POWER -> TASKS_CONSTLAT = 1 ;" to enable CONSTLAT, but when i printf("TASKS_CONSTLAT %d",NRF_POWER->CONSTLATSTAT); the result is still 0; how can i...
Hi,
I work on a BC805M module (nrF52805) with the sdk17.1.0 & S112. It is powered by a CR2450 battery.
I like to reduce the consumption of the ble_app_beacon exemple....
Hello,
I am using the nrf7002 ek and attempting to optimise the RAM assignment for the project. I have reduced the size of several thread stack sizes as well as the heap...
Hello,
I wanted to reach out about the issue I've been running into regarding the UART Async API. I am having trouble narrowing down what the cause could be.
I am using...
Hello,
I have BLE TX Mask failed to the spec. as shown in the attached image. It seems noise floor is high. TX outpower at +4dBm (see attached CLI). Please advise.
Thanks...
So, hello, hopefully I have done my diligence to be able to afford some help, thank you!
Context: driving an ADIN1110 by Analog Devices with an nRF52840 usb dongle. Within...
I am trying to install SDK 2.1.0 on a new computer. I installed nRF connect extension in VS code, installed toolchain 2.1.0, and then when I attempt to install SDK 2.1.0 I...
Hi,
I've been using dev kits like nRF9161-DK and when plugging them in to my laptop they all work with the Programmer Tool, "nRFUtil device list", and the nRF Connect Code...
To explain our problem: We have a system with a NRF52840 chip, we also have an external flash, the settings_subsystem is mounted in the NVS on the internal flash I have included...
Description:
I am working with an nRF52840 custom board. I have encountered an issue where the board is not detected by the J-Link debugger after flashing the firmware a...
Hi all,
In Sidewalk, the Lora we are using is connected to DIO3 through TCXO, which does not match the XTAL of sx1262 recommended by the official sid_end_device demo. Do...
I successfully read accelerometer data at 3000 samples per second . However, when transmitting the data over Bluetooth Low Energy (BLE) , I am only able to send 200 samples...
