Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
For Errata 149 on nRF52832 , TWIM send illegal pulse after clock stretching.
When using TWIS as slave device and TWIS require clock stretching,
Do they work correctly...
I have an issue with DFU via USB CDC ACM.
I would like to update the firmware using open bootloader over USB without softdevice.
I already tried to follow the thread:...
Hello,
I have a firmware working perfect with nRF52832 DK and nRF52840 DK, using SES 5.40a.
Now I just upgraded SES to version 5.70a. With new SES version, each time I...
Hi,
we are getting during NB-IoT attach (full AT dialogue below) for some nRF9160 SIPs:
URC: +CNEC_ESM: 29,0 URC: +CNEC_EMM: 19 URC: +CEREG: 2,"B414","000F6E21",9,0,19...
Hello,
I follow up this documentation https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/ug_thingy91_gsg.html#updating-firmware-through-external-debug-probe...
I try to run asset_tracker and asset_tracker_v2 on nRF9160DK. I observed that the default cloud Host Name is Amazonaws.com, which is shown in autoconfig.h file. see the image...
I tried to debug Asset_tracker_v2. During step by step debug, the program navigate to that part which is not included .. see the image. Also, I want to know, little more:...
Hello Devzone Community,
My name is Ted, and I am some way along development of Zephyr based firmware, running on an nRF9160 based custom board. I'm looking to put the board...
Hi,
How can we prove that the A-GPS is working correctly? We have run an experiment where we have use a module with A-GPS and one without and they have very similar (and...
Setup -
1. Sample used - nrf/samples/nrf9160/lte_ble_gateway
2. Board used to build - nrf9160dk_nrf9160_ns
3. NCS version 1.9.1
Steps performed -
1. Built the...
Hello Everyone,
I am trying to implement one wire protocol for interfacing MAX17211 fuel guage IC with NRF52840. I wand to know if there is any one wire library or any example...
Hi,
Do you have a suggestion for a 2.4GHz chip antenna? I sent a board to Ketil for RF tuning but the meander antenna ended up as too short. We would like to avoid a separate...
Hi there, I have been always using the dev board BLE antenna for the nRF52832-QFAB.. but now i need to reduce much more the size of the board, so i need a much smaller antenna...
