Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hello Nordic Team and Community,
I'm working on a fully automated Zephyr RTOS development environment on Raspberry Pi (Debian Bookworm) targeted at the nRF52840 Dongle....
Hello,
Is it possible to get logs (RTT) from an application started by a bootloader? As of now I don't get anything after the bootloader has jumped to the application start...
While running the BLE HCI USB ( bluetooth_hci_usb ) sample in Raw mode on an nRF52840 board, we observe a bus fault under specific conditions. The fault occurs when the device...
Hello everybody,
I am a research assistant at a university , responsible for maintaining and porting existing student lab exercises from the legacy nRF5 SDK to the nRF Connect...
Background:
My project is using the nrf54L15 with the 48 pin package. I'm using vscode with v3.2.0. The QFN48 package has the following pins bonded from the silicon to the...
I am trying to receive extended advertising from a device on nRF52832 .
I have made the following changes:
sdk_config
# define NRF_BLE_SCAN_BUFFER BLE_GAP_SCAN_BUFFER_EXTENDED_MIN...
Hello
Is there a possibility to build MCUBoot, SoftDevice, Firmware Loader and Application separately and then merge it manually? Or to build MCUboot + SoftDevice + Firmware...
Hello there,
I am working on a project which involves nRF52840 to scan and connect to specific BLE beacon.
So while scanning, nRF writes scanned data on UART. On same...
Hello,
I'm running SDK v.2.8.0 and developing using the nRF5340 Audio DK. I've successfully flashed using the buildprog.py script, and have set up my DK as an Auracast source...
Hi
1. At nRF5340 datasheet page 420, the PDM duty cycle is 40%~60%, any register can tune duty cycle? Or it's nRF5340 variation tolerance?
2. Since our DMIC IM69D128S...
Hi all,
I'm testing Skylo NTN on nRF9151 SMA DK with the latest pre-commercial/alpha NTN modem firmware (downloaded mid-December 2025).
Registration works fine, and uplink...
I am trying to get the nrf/sampoles/bluetooth/direct_test_mode working together with the code from zephyr/samples/subsys/usb/dfu-next.
I have the DTM mode running correctly...
Hello,
I think there is typo on page 541, in the PWM, Pulse Width Modulation, section of the nRF52840 Product Specification V1.11.
It states "pulse with modulation", but...
