Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Our existing product (already in the market) at Element Science in San Francisco, CA, USA uses an nRF52832 (BMD-350 module by u-blox) and nRF5 SDK 15.3 as base for the firmware...
Hello, I have two nrf52840-dongles which I am using to test ESB. (NCS 3.1.1)
With a few modifications to the ESB prx and ptx samples:
Remove logs except for PTX ESB_EVENT_RX_RECEIVED...
I upgraded my sdk from 2.6.1 to 3.1.1 and after resolving a few issues everything was working just as it was before the upgrade except for MCUmgr. When I run the MCUmgr client...
Hi,
I recently migrated a project from NCS v2.x to NCS v3.x and noticed that the method I previously used to generate a device-unique identifier no longer works the same...
I've seen similar threads but haven't yet found an answer that works for me. I don't know much about encryption but I've been tasked with adding 256-bit AES GCM to our project...
On a BLE Peripheral NRF52840 built with nRF Connect SDK v3.0.2 , high-rate GATT notifications sometimes push the stack into a state where no (HCI 0x13) events arrive for the...
Dear Nordic support:
How long is the single broadcast duration and the broadcast interval for Bluetooth? We would like to know what the duty cycle of Bluetooth operation...
I am trying to Build a modified version of the Matter weather station with additional endpoints I have created a custom Cluster and Custom Device type via Matter Cluster editor...
Hi，nordic
My ncs verison is v3.1.0;
Can I use ANT+ and BLE protocol together in nrf54l05 ？
Does garmin have ANT for nRF Connect SDK support nrf54l15 dk now?
If I...
Hello,
I am looking for ways to measure current during the transmit and receive test for the 2NR modules.
Can you please provide me the steps to do that?
Also what application...
Greetings, I'm developing a custom hardware using nrf9151, i've tested the gpio and serial interfaces of the custom module and the work fine, when i try to flash the serial...
I am in trying to use the AT client sample with an RS485 interface on a custom Board with nrf9151.
Other than the API states ( https:/https://docs.zephyrproject.org/apidoc...
Hello,
I want to use only LDO (not DC/DC) regulation on my nRF52840 design. The documentation states that LDO is the default for both REG0 and REG1, and that DC/DC should...
I read somewhere that the nrf52840 dk can change it's vdd via software, so it can be set to 3.3v, thus it can program a nrf5340 device with it's internal j-link debugger....
