When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I am working on a PCB with the nrf5340 and I have been following the reference schematics and the hardware files from the audio DK. I want to have the bare minimum...
Currently, I have configured cs-gpios in the device tree and loaded the SPI in the main function. Why is D0 (representing CS) kept high in my experimental waveform, and SCLK...
Hello! Some time ago we bought your NRF54L15 dev kit 0.9.1. ( for channel sounding BLE6) with an aim to make a product for staff positioning at underground mines. For this...
I used the application_update example, added external FLASH support code, and incorporated the nrf\samples\wifi\scan code. Initially, the NRF9151 and NRF7002 communicate normally...
Dear All.
I tried to test and evaluate LoRaWAN stack on Zephyr, without success. I will need more time to debug what is happening by the logic analyzer. Meantime I attached...
Hello everyone,
We’re developing a prototype using the nRF52840 MCU, and we need to flash a bootloader over SWD using a 1.8 V system powered by a PMIC. I’m exploring whether...
Hi,
I have a question on the correct usage of queues in Zephyr.
I have a firmware program that uses multiple threads, and as it has developed over the years multiple threads...
Hello,
We are investigating a sudden battery drain issue in our nRF52832-based wireless product. During power profiling, we noticed unexpected current glitches (please see...
Hi,
I have nRF54H20, SDK 3.1.0
is there any sample (tested) which is running with high speed peripheral? I need to test high speed SPI (SPI120 or 121).
I found (....
I am trying to get an end to end BLE application working. I have an nRF52832 board that is running peripheral_uart. It is advertising and sending a text stream to the connected...
Hi Nordic support
We have ealier used your legasy SDK16.0 on nRF52840 where we where programming our device serial number in the UIRC area.
NRF_UICR->CUSTOMER[0-4] where...
Dear,
I was trying to flash a custom board using a nrf5340 module (Raytac MDBT53-1M) threw P20 connection of a nrf5340-DK like described in https://infocenter.nordicsemi...
Hello, i am already 1 week trying to make tracing working. I have NRF54L15DK and SEGGER J_TRACE PRO. I solder trace port on the board.
I did enable => nRF TPIU in nRF KConfig...
