When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I'm currently attempting to get the nRF 9160 to enter PSM mode when not transmitting along with the asset_tracker_v2 application just so we can do some power consumption measurements...
Hi Dev Zone,
We have an existing design that includes the Espressif ESP8266 Wi-Fi MCU and we would like to add an nRF52 to the design. Our preference would be to add the...
I'm using NRF52833 with SDK v16.0.0 along with mesh SDK v4.1.0. I want to know if it's possible to write data which is not word aligned into the internal flash (For example...
Hi everyone,
I started working on nordic nRF52832 DK and tested out some examples. I think i am done with the examples now and am looking to write my own code apart from...
Dear Members,
How can we determine the first ANT message from my transmitter ?
We saw from ant_parameters.h,
Which variable is being used ?
Kind regards...
Hi,
Today I found that after I OTA my board, it runs well at first. But when I reset it, it will run old image again.
Before this OTA, my board has gone through many OTAs...
hi all,
I am currently working on a ble project, the led based on the NRF52832 chip is used as the slave, and the mobile phone is used as the master to form a star network...
I use nRF Connect to connect to nRF52832 device. 1st connection is bonded authenticated encrypted link, but 2nd connection becomes not bonded unencrypted link. Why 1st and...
Hi,
I was provisioning devices for a customer today when I noticed at the end of provisioning that the JSON database file that was exported had all the features except ...
Hello,
We are developing a library which is intended to use the trustzone feature available with nrf5340 DK. We followed the instructions available in Using a custom Secure...
Hi
When I use the nrfjprog with the command line:
The application is starting and the code running.
If I do the same again (with the same hex or a newer one) the...
I am developing a project with nrf mesh SDK 5.0.0, I use dimming code, but the code uses rtt input, if I want to replace rtt with buttons, what should I do? I'm learning,...
Hello! I will try to make this as simple as possible with the details regarding this issue What I have
nRF52840 DK (pca10056) (As BLE sniffer)
nRF52 (pca10040) (Used...
Hello
We are using NRF9160 AssetTracker 1 and MQTT to AWS. We have a AWS Certificate, Root Certificate and Public and Private Keys on the device.
We want to start testing...
