When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I'm trying to get the maximum possible throughput from a peripheral device, sending notifications to a central. I compare the throughput between 2 PCA10040 boards...
Hi,
I'm using s140 trying to connect up to 8 devices to windows BLE adapter and BluetoothLEDevice object, I have 2 problems,
1- the maximum throughput with different configurations...
Hi All!
I am using Segger Embedded Studio and nRF5_SDK_v15.0.0 .Available kits for testing are nrf52833DK and rak4630(nrf52840).
We want to test nRF52833 support on long...
Both NRF were programmed thru USB NRF connect for Desktop programmer.
Both NRF are running the same soft properly.
To demonstrate the final look and put the dongle in...
Hello,
In my project i am using nrf52810 with my custom board for pushing data to UART so i have used UART example code for this but UART pins are connected 20 (TX), 25...
Hi
I'm working on a Zigbee network, and I want to have a few End Devices (ZED) connect to a Coordinator (ZC). And it's fine, I got that working by using the zigbee_default_signal_handler...
hi
i develop software with the nrf52dk, success with program it with nrf command line tool.
now i want to program the application on the nrf52 dongle but with no success...
I am trying to use SDK version 17.2.0 to develop a package (Boot Loader + SD + Application) for our product based on the PCA10040e board with an nRF52810 SoC.
I soon realized...
There is a serial interface in the nRF SDK that makes it easy to serialize mesh data over serial
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am want to read Analog value from LDR sensor. I am unable to find ADC Input pin in nrf52840 Dongle datasheet but I got it in nrf52840 chip datasheet (page -576...
Hello Devzone Community,
I have a question set regarding correct, best way or ways to configure nRF9160 GPIOs for high impedance. My hardware is a custom board but shares...
I have the nrfConnect task that builds my project in vscode.
I need to add a script to execute before the nrfConnect task.
I added a task to my tasks.json but the task...
Hi,
Could you please tell me which firmware is flashed onto the thingy91 by default (both for the nrf52840 and for the nrf9160) ? Where can I find the source code for these...
Hello,
We are experiencing a strange issue when quickly turning off/on the NRF52840 on our board. In order to check whether the MCU wakes up correctly, a test fw was set...
