Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hi,
I am developing with nRF52832, SDK 15.3
I have an issue with sending data over NUS service. When I flash the code to nRF, it starts advertising, but when I connect...
Dear sir,
The twi sensor code in SDK14 is getting stuck at NRF_BREAKPOINT_COND. Also, on the uart terminal it is showing FATAL ERROR . Please help me out of this.I am using...
Hi
I want to set up a network of about 4 groups of BLE light modules(using the experimental dimming example). Each group comprises of 5 to 7 light modules.
Currently the...
Hello, my code was working just find then I tried to add the user description value to my characteristic. In the example below I had set it to "Test" for now. Once I did this...
hi
i am programing BLE blinky app blinky which advertise. yes, the same code i am trying on custom board works on nrf52DK which has LFRC crystal activated as mentioned on...
I am trying to add my nrfcloud certificate to my nrf9160-DK but the AT commands do not work due to a timeout.
My procedure is as follows:
1) Downloaded the "nrf9160dk_fw_2020...
Hello Nordic team,
I'm getting started with BLE, using the 52832 SDK16 HID mouse example. In the example, clicking the button only moves 5 pixels. How can I move the cursor...
Hi! When measuring current draw with the NRF52 in idle state, we've noticed current spike at seemingly random times. when investigating further, we've discovered these spike...
Hi,
I am looking for an implementation on DotDot App layer over Thread and couldn't find it anywhere. I want to implement dot-dot for Light, Temperature and Humidity Sensors...
Hello, I want to purchase an nrf52 development board. I am currently using nrf52832 module (MDBT42). I wonder which DK should I purchase nrf52832 DK or nrf52840 DK? I am asking...
Hi,
I am trying to store data to flash with the support of FDS module while using Mesh. I'm currently using NRF52832 with NRF5 SDK 15.0 and Mesh 4.0.
I have tested flash_fds...
Hi Support Team
I try to run the http_client sample based on ncs1.2.0, and I use the following configs because only NB-Iot available in our location:
when start running...
Hello there,
We faced the new issue after the iPhones are updated to the iOS 13.4. I tried to find the issue solving on the forum and looks like it is the new one.
We...
Hi,
I'm evaluating the new nRF5340-PDK and trying to put the device in low power mode. My steps so far:
Cut SB40 to allow measuring current via P22.
Connect power...
Hi,
I am trying to store a buffer which i collect from ble connection. I have tried sd_flash functions first. I could not found any examples so page number or addresses...
