I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
My nRF52840 was recently corrupted. I was able to run through reset and downloaded the latest MCU 'J-Link OB-SAM3U128-V2-NordicSemi 170724.bin' onto the board. So now it shows...
We are preparing a product (based on nRF52840) for manufacturing and currently defining the production test process.
The product is hermetically sealed with no external...
Hello,
I'm currently implementing a multi-endpoints Zigbee device using an nRF52840.
This device is a router which have several "GROUPS" clusters (one in each endpoint...
Hi,
I've nrf52840, s140 with SDK17.2 and I was able to set REGOUT0 to 3.3V in 2 ways.
or
nrfjprog.exe --memwr 0x10001304 --val 0xFFFFFFFD
After that I do...
It is my understanding that the more antennas you use for AoA the more memory is required. I am trying to gauge how much memory and resources would I have left for other application...
Is there a way to configure the serial LTE modem application to communicate through the UART using a 2-wire Tx/Rx with Hardware flow control disabled?
I have read that you...
We are trying to switch main MCU that we use in our products into NRF52/53 series devices. We've chosen NRF52833 (aQFN73) for one of these devices. Is it possible to use only...
Hi,
I have a question about the LwM2M Client implementation for the nRF9160.
Can the LwM2M Object updated in a registration update or it is relying on a re-registration...
I have a situation where a customer needs to DFU some nRF52840 custom boards that we shipped. The firmware that I wrote used extended advertising and thus appears as a Bluetooth...
Hi,
I tried running the crypto sample example as part of the nRF SDK project on my nRF5340 DK.
I successfully completed as few tests and then fails while trying to run...
Hello Nordic Team I want to use the ble_app_beacon example found in SDK 15.3 on NRF52810 when NON_CONNECTABLE_ADV_INTERVAL is MSEC_TO_UNITS (5000, UNIT_0_625_MS). The program...
We are using the QDEC in an nRF52832 and our rotation speeds are 0 to 15rpm, usually around 10rpm. Is there any fundamental reason the QDEC can not be used in this case? We...
I'm trying to get the bmi160 sample to work with my custom nRF9160 board. I think the sample is quite old and not maintained. Unmodified (except fixing pure compilation errors...
Hi.
I am building an I2C driver for the Sensirion SPS30 particle sensor (datasheet: https://no.mouser.com/datasheet/2/682/Sensirion_PM_Sensors_SPS30_Datasheet-1888453...
Hello!
Im trying to change my application. Right now everything works with bonding. DFU and reading and writing characteristics. We have noticed a lot of clients unpair...
