Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hello,
I have got three nRF52840 Dongles to test Bluetooth mesh. I have been going through the devzone queries and found that many people have previously asked about SDK...
Hello,
I am using the nRF52832 with the s132 SoftDevice. I've been trying to interface the VL53L0X sensor to get ToF readings. I'm using the code of this driver . When calling...
Greetings!
I am using NCS 1.4.99. I have spent some time debugging my I2c application on NRF5340 and I came to the realisation that I was not able to control any pin that...
Hi,
I'm developing a program using SPIM instance 1 on nRF5340 PDK, with nRF Connect SDK 1.4.0.
The problem I met is exactly the same as this post . If I want to use a...
NRF52832, nRF52840 is under consideration for development. Because of the implementation of Secure Boot and Secure Key Storage capabilities, we want to choose the nRF52840...
Hi,
I was able to upload a binary file before, but not able to upload a binary file to nRF connect app in order to FOTA.
Could you please help me to upload a binary file...
I am trying to compile and run the ble_app_hrs example for an nRF52810 dev board, using Segger Embedded Studio v5.34. I am using nRF5_SDK_17.0.2_d674dde, with s132. This is...
Hi,
I am looking for a working example for upgrading the MCUBoot itself when we have the configuration B0+MCUBoot+APP, especially wrt to SLM application.
I have gone through...
Hi, I am developing using Segger Embedded Studio.
I downloaded the module and checked that output/debug/Exe has a .hex file.
Then can I download this output file back...
Hello,
We are testing Angle of Arrival feature which was released in Bluetooth v5.1 We are currently using Texas Instrument CC2640R2F and TI angle of arrival board to...
Hi,
I'm using nrf52840 with BLE functionality.
I don't use sd_ble_gap_tx_power_set in my application.
Does it mean that I'm using default power (dbm)?
What is the...
Hi,
i am trying to interface an external spi flash memory with nrf52832 to store temp. data.
i tried to read the manufacture/device id but i am getting wrong data.
my...
Dear Sirs
We are planning to have our end product certified by FCC and CE. It uses the nrF52840 SOC directly on our PCB. This has the following QDID : 124988.
We have...
I am using cjmcu 8223 board for my project so for uploading program I brought a ST-link V2 pen drive like device but I can't able to detect the board on the ST-link software...
