I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
I am trying to test 1 central 4 peripheral multilink(with saadc).
However, when the master-slave(central-peripheral) is connected,
the connection disconnected...
As the title states, my program (and a simple idle/hello world program for that matter) pull approximately 600-800 uA at idle. Same exact program, driver, and config on my...
Hi all, I am trying to write a driver for a TMP116 temp sensor based off the existing Zephyr TMP116 driver. I have added in functionality to enable the interrupt pin to enable...
1. I am tried to clear DTLS session during lwm2m session using coap_security_destroy() . I have added logging and I can see ntf_tls_free() is called from coap_security_destroy...
I'm using DWM1001-DEV, which has UWB and nrf BLE features, and my ultimate goal is replicating Apple's Airtag with DWM1001-DEV. For this, I have to ensure the power consumption...
Hello. Our company develops an electronic device, that includes using of Bluetooth Low Energy technology. We do not familiar yet with the benefits of being a Member of Bluetooth...
Hello DevZone.
For my project I am using up to 6 connected peripherals to my central and I was watching the behavior of the link when one of the 6 devices disconnected...
Hello, I am brand new to antenna design and especially antenna tuning and want to know if my antenna tuning design/method would work.
First I will be tuning with a VMA ...
Hello,
I am using a nRF9160-DK(PCA10090, 1.0.0) and v1.6.1 SDK
I am trying to estimate battery consumption in some scenario.
For this test, UDP sample is used.
When...
Hi,
I am using a specific LED that has the PWM specification to drive as below.
Would it possible to drive the LED with nrf52840. I see the PWM clock upto 256KHz...
Hi Sir/ Madam,
I want to create a modul to scan and advertise data using Nordic Dongle , (PCA10059). The example code in sdk , ble_app_multirole_lesc has been tested with...
Hi Forum,
I'm using a NRF24L01 (without "+") in a very power critical application. To tune the matching networks, i used a mini coaxial connector on the output to measure...
I'm developing an application for the nRF52833 using NCS 1.5.1, and currently working on performing a DFU using MCUBoot. I am sending the app_update.bin file over UART from...
