I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
My goal is to establish a BLE connection between the DK and the smartphone, using NFC for the OOB pairing . I am using the nRF52 DK and the nRF5 SDK , v.16.0.0.
The intended...
Hi,
I am having issues with getting SPI up and running on my nrf52840-DK using NCS. I've tried getting support about this in another ticket but it seems like it lead to...
Hi,
We are using the nRF52840 SoC.
The following image is taken from the datasheet:
It shows a Gain block before the SAR core
a. Does the Gain block serve also...
Hi ,
I want to know if it is possible to close/open the uart connection with RTS and CTS pin in order to have a low power UART?
When RTS and CTS are high, uart is closed...
Hi,
Can any Zigbee application receive ieee radio interrupts in both TX and RX path?
What I need is:
In the case of Zigbee Tx, an advance notification of 200 μs would...
Hello, I am using nRF52 DK and softdevice s112, developing with SDK V15.2. I am exploring the fds library and have encountered some strange behavior. When I connect the nRF52...
Hello,
I am using nRF52840, S140 v7.0.1. We want to measure distance between two nRF52840 with BLE 1 Mbps and 0 dBm.
I am referring below two links.
In this its...
Hi,
We have 2 microcontroller on board. One of our micro controller will update nordic chip using serial DFU without any signed keys.
For testing purpose i am implementing...
Hello,
I'm new to Nordic products.
I have BL651 module and I want to connect it to another CPU over UART. So my question is how can i do it?
I've found in some other...
Hi Team,
We have used the "CC310" and "mbed TLS" both the crypto engines in my application with conditional compilation on NRF52840 soc.
We have measured the timings...
Hi,
We are using nRF52832 chip along with soft device and nordic SDK. However we have our own custom boot loader and that doesn't have soft device.
We want to implement...
hello,
I am using SDK 16.0 and I use flash storage to store some value which is critical for our application, when I use fstorage_write as below inside main(),
int main...
I am trying to use the fstorage library to store some data for my application and use the flash_fstorage example in SDK16 as a starting point and copied the required codes...
Hi
i am getting Fatal error while uploading code in my nRF52823 plz find attachment which i enclosed.
and showing break point at NRF_BREAKPOINT_COND; plz tell me what...
