I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hello!
Using SDK v2.6.1 and the nRF5340 Audio application, I want to use an external button as button5 instead of the one that is on the board.
I noticed that if i change...
Sometimes I just want to compile a single file for an nRF Connect project with VS Code and the nRF Connect extension. This sometimes fails because an include file isn't found...
Hi.
I am updating an nrf9160 B1 project on a custom board in SDK 2.1.0 to SDK 2.5.3, and I am running into a problem when building. This error does not show up when building...
Hi,
Hello, I have a project that's working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a so many threads on this...
Hi DevZone!
I'm currently developing a device that has several hardware actuators and I've implemented 2 OnOff Models each belonging to an element. But right now I'm having...
Hello there!
I'm trying to enable secure boot via CONFIG_SECURE_BOOT and am currently getting the following error:
I'm using zephyr via sdk-nrf v2.6.1
Searching the...
Hi,
I just try to use the DFU over USB to upgrade the FW but i found one problem which is the process will erase the external flash data
but i put the some sensor FW data...
I'm upgrading from SDK version v2.4 to v2.7 which introduces the new Zephyr hardware model and I'm struggling with the transition. I have two custom revisions is based off...
Hello,
I am using nrf7002dk on NCS version 2.6.0.
I want to send data to an HTTPS web server using WiFi.
I saw some mentions about HTTPS in several posts on Devzone...
HW/SW Versions:
nrf52840 Dongle DK
nrf Connect SDK 2.5.2
Issue:
I'm developing a Zigbee device based on the ZBOSS, using an nrf52840 dongle development kit and there...
Hi,
We have developed a nrf5340 custom board powered 1.8 V. So we cannot use the nordic DK board to program it.
I would like to know if there is an interface other than...
I have an application where I am using the SAADC to take ADC samples. At any point during the measurements, I want to be able to stop the samples prior to the ADC buffer filling...
Hi,
I trying to adapt the ble_app_multilink_central example to allow more than 8 peripheral connections to the central device. However, when I change NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi,
I am using nRF52832 board and I want to understand the current consumption in the board will differs while running the code in zephyr RTOS platform and without zephyr...
Hi,
I would like to know where Matter's commissioning ad timeout is set.
I understand that it stops after 15 minutes, but I don't know where it is set.
Best regards...
