When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I am working on nrf52832 and SDK V15_3 and Softdevice S132 . I want to enable 2MBPS mode to achieve maximum throughput. I have checked different links in nordic devzone but...
Hi , I succeed to flash the firmware to Thingy52
you can see the attached 2 pictures one is for the nRF Mesh app and the second is the Thingy 52 (Four units) which are ...
Hello,
I am using nRF52840 DevKit, SDK 16.0.0 and SoftDevice 113 v701
I am looking at nrf_bootloader example and want to configure a watchdog that keeps running even...
Hi,
I'm wondering what is a good way of keeping track of when the device is inside the active time window so that the data is being sent at the correct time.
Here is my...
Hi,
I'm working on two projects, in the first one, nRF52832 (softdevice S132 V6.1.0) is used as a slave component communicated with STM32L4+ over UART and the second one...
Hello,
I have been using nRF52840-DK and also nRF52840 Dongle for testing and I found an interesting behaviour when I established my test setup. The RF module acts as an...
Hi All,
We have a product based on nrf52832 that has a custom ble service with 2 custom characteristics.The first one is to send data to the nrf device and the second one...
Hi
I opened the Watchdog in the user application,and do nothing in the bootloader.Then when I use DFU,the CPU reset appears.How can I to deal with it?
And when I upgrade...
Hi
I am looking for some specific contract developer help to build and Android app to update Firmware in devices using DFU and the buttonless service. Obviously there are...
HI,
We are evaluation the nRF9160 in the devkit and we are trying to obtain the values specified in the nRF9160 Product Specefication v 1.1. After following the different...
Hello,
There are many questions out there on correctly determining the SAADC pin input voltage limits. The equations given in the product spec is very straight forward:...
We are creating and application that will use the Serial port to communicate to a host using an RS485 protocol. We have it working in SDK 15, but we are now trying to build...
Hello All, I want to generate Bi-Phasic two PWMs with 180 degree interphase delay and variable Duty Cycle with variable frequency upto 250 Hz in nRF52810 SoC. Can you please...
Hello, how can I use the functions in nrfx_twim.c
Using SES and the CMSIS config wizard, I have picked:
NRFX_TWIM_ENABLED 1
NRFX_TWIM0_ENABLED 1
NRFX_TWIS_ENABLED...
