I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
I have an application with 2 SPI IC connected to the same SPIM port of nRF54L15.
These 2 ICs have different SPI mode:
A: SPI Mode 1 (CPOL 0 CPHA 1)
B: SPI Mode...
Hi,
We are working on a custom design for IoT cellular communication (NB-IoT), using the nRF9151. We've done some testing with the SMA DK, and are at the stage of PCB...
Hi. I am looking into measuring radio channels' qualities by using Energy Detection (ED). But for the examples I've tried so far, I've been getting zero for all the readings...
NCSv3.2.4
Is AoA CTE supported in the nrf52811 ?
Product page https://www.nordicsemi.com/Products/nRF52811 says " The nRF52811 SoC supports Bluetooth LE, and is capable...
Dear Nordic Team,
I am working on a custom board using the nRF5340, and I have configured SPI with the following pins:
SPIM_SCK → P0.08
SPIM_MOSI → P0.09
SPIM_MISO...
I really need to verify this design for nrf54L15 SoC. If someone can go through it and confirm if it is okay or I need to make any changes ? I had made nRF52832 board but...
I am not sure if this is an issue with the nRF Connect extension or the my Thingy91 but when I use the "Flash" button in the actions tab of the NRF Connect extension to program...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
I am trying to enable the Channel Sounding feature on the nRF54L15 DK by sending HCI commands over a "USB to UART" interface. For this purpose, I created the "hci_uart" sample...
Hi,
I'm developing a Channel Sounding application on nRF54L15 and trying to understand how the different TX power settings interact.
I have a few questions:
What does...
DevZone Post: Custom nRF54L15 Board Not Recognized by Kconfig (Falls Back to Apollo4X)
Summary: I am bringing up a custom board based on the Raytac AN54L15Q (nRF54L15)....
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
HI
I’m currently using NCS 3.2.1 , working with the periodic_adv_conn sample.
On the advertiser side, after receiving data from a node during each periodic sync broadcast...
