Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi Nordic support:
Our product uses nRF9151 module, we are going to do GCF certification field test. Could you provide some guidance on the following issue?
How can...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
I am setting up Segger Embedded Studio on my M2 Macbook and running in issues.
I downloaded S140 (nRF5_SDK_17.1.0_ddde560) and upon the build, I see the following errors...
I have a nrf9160dk that drives a screen via SPI, using an IT8951 controller. The firmware driving the screen works fine if I plug the USB cable on a power bank or using MS...
Hi, I'm getting an error when building the example program blinky that says: ".text is larger than specified size" and ".rodata is larger than specified size".
I'm using...
I'm following the steps in exercise 1 of the nRF Connect SDK Fundamentals and getting configuration failures. From what I can tell it looks like Zephyr is failing to build...
nRF Connect SDK v3.2.0
Write code:
Read code:
Log:
The address seen on the phone is usually not "06 05 04 03 02 01", but sometimes it is "06 05 04 03 02...
After the PPK II had been stored for a long period of time, it was recently taken out to measure current. It was observed that, regardless of whether Source Meter mode or...
Hi all,
I have been attempting to get the nRF Connect VS Code extension setup to try out some samples on the nRF9161-DK board.
I'm currently having a problem with a version...
Clarify the minimum mandatory external connections and pin/rail requirements for an nRF9151 to boot and run a flashed application, and determine why serial_lte_modem (SLM...
Hi,
I'm working on an application that I recently updated to ncs v3.1.0 (from v2.9.1). For most of the development, I have been working with the nrf54l15 as build target...
HI
I have replaced the external flash used with the nRF54L15 with a different model. How should I set the sfdp-bfp parameters for this new flash?
Thanks!
Using nRF5340-DK, nRF Connect for VS Code 2026.1, ncs v3.1.1 I'm interfacing over a SPI bus to a custom ASIC that uses MISO as a sort of RTS/CTS kind of idea. While CS is...
Hello,
I'm experiencing an issue where RTT logs stop appearing after MCUboot jumps to the application on nRF52832. The application is running correctly (BLE advertising...
