Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
MCU: nRF52840
IDE: Keil uVision 5.17
SDK: 15.2.0
Board: Custom
OS: FreeRTOS
Using MicroLIB
Hello,
I am currently working on a FreeRTOS project that leverages...
Hi,
Based on the below extract:
"Because older devices that don’t support Bluetooth 5 will not be able to discover extended advertisements, an advertising set with legacy...
Hi, I am currently using the PPK2 for current measurements.
According to the datasheet, the PPK2 supports a maximum source voltage of 5 volts. However, my device requires...
Hello
we are certifiying our product by ISO 13849-1 which includes the Nordic nRF52832, among more information I would like to start with the following questions
1. where...
Dear nordic support
We're in the concept phase of a product that implements cellular cloud connectivity.
We already implemented a "blueprint" ESW which provides supporting...
Hi,
I am planning to create an ultrasonic library (based on ch201) because I can't find any library for it. So I am porting code from ch201 development kit to nrf52 custom...
Hi there,
I have a Thingy:91 board and I would like to enable the accelerometer data to be sent to nRF cloud when using the Asset tracker v2 application. I saw that it is...
Good afternoon,
I'm trying to understand how the RTC works on the nRF52.
The RTC can run when HFCLK is OFF and PCLK16M is not available
Section 25.5 describes the TICK...
It appears that KConfig is uable to find any compilers for native_posix with VS Code on windows 10 after installing all recommended packages and prerequisites during SDK install...
Hello,
I am using LwM2M library in my project and I want to check what version I am using of LwM2M carrier library. Please correct me if I am wrong, is according to below...
I am creating software for a proof-of-concept device using the nRF52840 Dev Kit and nRF Connect for VS Code.
I started a few weeks ago with the Nordic UART Service code...
With Zephyr, I am using BLE Stack sample (rpc-host) on net core and peripheral_uart on app core. I changed the uart pins on from the standard dvk configuration on devicetree...
Hi
I was wondering why there there seems to be no information about profiling of the LC3 codec by T2.
Only information I found is from Karl's answer here :
The rule...
Hi~ I have a new NRF52832 REV3 xxAA board, and I need to read its SRAM value. However, when I use the JLink command to read it, I get 0. I have tried recover and eraseall...
