I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hi,
nRF52832, SDK 17.1.0 with Softdevice S132.
Softdevice sleep does not work when advertising. Application flow is to advertise one packet, then go to sleep for X seconds...
Hello,
I use a PKK2 for power measurements on a nRF9160DK and Feather nRF9160 from circuit dojo. With the UDP example to test it out the sleep current so I can determine...
Hi Sigurd,
I'm finally using the mcuboot and mcumgr_cli I worked on in summer of 2023. I generated the mcumgr_cli for debian with go lang back then. I'm building my app...
Hi Nordic team,
We are currently investigating how to ensure that the fuel gauge continues learning and retaining the battery's charge/discharge profile over time.
In...
I am using Zephyr 2.9.0 with the sdk-nrf repo v2.9-branch checked out. The locator_tag sample builds without issue and flashes to the nRF54L15-PDK without issue. I have a...
I'm trying to use raw packet transmission (IN combination with wifi promiscous mode and raw sockets eventually) with my nRF WiFi device. I have both the sample raw_tx_packet...
Dear DevZone,
I would appreciate your assistance in understanding how to correctly configure Wi-Fi and BLE coexistence for the nRF5340DK and nRF7002EK with SDK version 2...
Hi! I'm testing the application with the custom Battery pofile I generated with nPM PowerUP app. During testing I found the issue with the SOC value calcultation depending...
Hi Nordic Team,
I am planning to develop a SmokeCo device using the nRF54L15. I tested the example code of Smoke-Co from nrf-sdk with nRF54L15-DK and that working correctly...
Is there a trick to getting nrf_dm to compile on the nrf54l15?
I've installed v2.9.1
Command I normally use (nrf52840):
west build -b nrf52840dk_nrf52840 -d build_nrf52840dk_nrf52840...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
Currently, I am trying to use GPIOTE PORT...
I've been trying to run the example Mesh/Chat on NRF7002DK, and the terminal print <err> bt_mesh_pb_adv: Failed enabling advertiser and <err> bt_mesh_pb_gatt: Failed enabling...
After using the backup v2.9.0 project to overwrite the original project, I encountered the following issues during compilation： How to solve it? Using Windows not Linux. Thank...
Hi Devzone
We found that the NRF54L dk will stuck if add systemView function into the bluetooth sample project
we add below config into peripheral_uart/peripheral_lbs...
