Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Dear
I'm working on controlling an I2C device.
I want to achieve TX->TX using the nrfx_twim driver. I specified NRFX_TWIM_XFER_TXTX. When I looked at the nrfx_twim source...
Hello,
During design and schematic entry I used the online datasheet to select GPIO capability. I was advised that I should try out the pin planner to confirm that pin choices...
I am using the nrf_fuel_gauge_idle_set function to handle the fuel gauge state when the system enters a low-power mode. When the charger is connected, I exit this state and...
Hello Nordic Support Team, I am experiencing an issue when using MQTT over an NB-IoT connection with the nRF9151 DK, and I would like to ask for clarification and guidance...
Hi,
I am working on a Matter device based on Nordic NCS v2.9.0, using Google Home as the OTA provider.
I have successfully uploaded a new OTA image in Google Console,...
n the nRF52805, if the hardware is configured for DC/DC regulator operation—namely, with the DCC and DEC4 pins connected through the designated inductor and capacitors—does...
I am using a Thingy91x, with some additional sensors attached via qwiic cable.
Initially to test the Thingy91x I inserted the SIM and scanned the QR code on the Thingy91x...
I am developing a proof-of-concept for remote controlled super-low-power devices using PAwR. I started with nRF52840 (for boths, clients and remote) and now migrated my code...
I built and ran the Matter Light Bulb example for Thread and was able to commission it into Home Assistant with no issues. However, when I tired the Matter Temperature Sensor...
Hi
Setup: nPM1300, nRF54L15-based board, SDK 2.9.2
I am trying to figure out how to use the nPM1300.
So far, I have not succeeded. Quite frequently, after power...
Hi,
I downloaded the NCS v3.2.0, but always got the error below when u npacking the toolchain , the same error when downloading via Vscode. and there is no problem for v3...
Hello all, I am using the nRF52840 together with the nRF7000. To save GPIOs, I would like to use the BUCKEN pin (which is directly connected to the nRF7000) also as the enable...
I tried to compile the project according to the link（ https://github.com/nordicsemi-neuton/nrf-edgeai-thingy53-ble-remotecontrol ）, but the compilation failed.
The compilation...
Hello Nordic Community,
I am working with the nRF5340 SoC as the master and trying to configure a PDM microphone . I have two related queries regarding PDM/DMIC operation...
