The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
I am trying to implement a Low Power Wireless technology to get sensor values from more than 10 devices at a time. On doing research, I found that the Thread Topology...
Hello, we have built a custom nRF9160 board with different populations for the GPS antenna, now we would like to do some tests to find out which variant offers the best signal...
Hi!
The posts I've found regarding this were quite old, and they mentioned features which then were coming.
So I'll ask anew: Is it possible to use AT-commands through...
Hello,
I would like to ask you if SoftDevice S132 v.7.x.x allows Master-initiated Feature Exchange procedure?
BLE Core spec: Vol6, Part B, Cap. 5.1.4.1.
I tried to find...
Hi everyone, I use nrf52833 to make dongle. My test found that after suspend of usb, I tried to enable ESB rx mode, but I couldn't receive rf data. What is the problem?The...
Hello,
When deleting a bond from the central, after trying to reconnect with the peripheral the PM_EVT_CONN_SEC_CONFIG_REQ gets called as expected. I know that allow repairing...
I have been trying to develop a project, my custom board has a nRF52840 chip and I have a nRF52840 DK too.
My problem is when I try to debug any example from any SDK....
Hi, I attended the Nordic Seminar in Tel Aviv last week and heard several lectures from your experts.
It was recommended that we use a module with Nordic IC rather than...
Hi,
I am using vscode and nCS on windows, kindly help me with below 3 queries:
1. How to generate a binary signing key, say "KEY_1"..?
2. How to sign a binary with...
Hi,
We are trying to use PPK2 to measure current of our board, we want to receive the data from PPK2 and parse by our owner python script, so could you provide the protocol...
Reading The adhoc smart waste solution uses the nRF9160 SiP I tried to reproduce the mention 6 µA with LTE-M in eDRX with an interval of 655 s.
I use
CONFIG_LTE_EDRX_REQ_VALUE_LTE_M...
Hi,
We use PPK2 very conveniently as a logger for testing.
How about adding the supply voltage as display options also?
We hope you will consider this.
Thank you...
Hi dear,
It is possible to establish parallels multi connection to different J-LINK's devices serial numbers via nrfjprog.dll, or any other automated way ?
We successfully...
Hello, I'm making a breakout board with nrf52832 qfaa. I used chip antenna (2450AT18B100E) and followed Nordic reference layout. I am getting around 60m range in an open environment...
