Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello,
I got two PCA10056 1.0.0 DKs equipped with an nRF52840 rev. 1 (code AC0). Both do not measure the VCCH voltage correctly (displayed voltage ~2.4V instead of 3.0V...
This forum feels pretty advanced, so if this is the wrong place to ask this question apologies and please let me know where I should be asking it instead.
My goal is to...
Hi,
I'm developing on the current setup:
nRF52833 DK, emulating an nRF52820.
Soft Device 113 version 7.2.0
SDK 17.1.0, with updated MDK (see link )
IAR EW ARM...
Hi Everybody,
I need help in writing a little software on NRF52805 which will active the transmitter with parameters:
1) Frequency : 2402Mhz only. (and i will later...
Hi,
I'm using nRF52832 with S140 v7.2.0 base on nRF5_SDK_17.1.0. I use PCA10100 development kit and set VDDH/5 as input and use internal reference (0.6 V) to do the battery...
Hi
I am working on SPI implementation on BL653_dvk board and while SPI_transfer i want to capture the timeout error.
but not able to differentiate which timeout is correct...
Hello,
We are using MDBT42Q-512KV2 module which is based on nrf52832. There is Central and peripheral ( Foot Pedal Switch ) using same module.
We have used crystal from...
I know from the product specification for the nRF52832 chip that the high frequency clk can use a external 32 MHz crystal as source. My question is, is it possible to supply...
Hello!
I am now developing a product with NFC based on nrf52833.
I need to transmit some crucial data between device and phone, such as device settings.
But I have...
Hi all,
I would like to measure time intervals between gpio edges along with Matter.
I tried to use a 100us timer interrupt but seems it will crash the original matter...
Dear Support
I have made the following findings of my evaluation of the NRF5340 with Version 2.1.0 SDK:
-CIS mode has no constant delay at default settings 48-4. According...
Hello Nordic team,
I have looked at the BLE + Zigbee multiprotocol examples from nRF5 SDK and in these examples, I see that there is a file ' multiprotocol_802154_config...
Hello,
are NRF SoCs considered as BLE certified?
What is the default firmware in such case?
I guess no fw changes are allowed so that certification remains valid, right...
If I only wanted to allow one bond at a time, how could I do this?
For example when someone connects for the first time they would pair and bond, by entering the passkey...
