I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi，nordic
I am using ses6.22a, the sdk is 1710 and mesh5.00. When I integrate the serial port case into the mesh sensor case, the serial port can work normally, but it must...
Hello guys, i'm attempting to record the radio_end event, and i tried to enable it with the following code:
However, the second line constantly crashes the chip.
In...
Hi:
I used the following command to install matter OTBR, but the following error occurred when executing this command;(sudo docker run -it --rm --privileged --name otbr...
hi,
I would like to purchase the following nRF-Desktop. It is a wireless BLE keyboard and mouse set.
https://www.nordicsemi.com/Products/Reference-designs/nRF-Desktop...
Hi,
I am using the nrf9160 and attempting to enable MCUBoot and secure boot. Is it correct that you still cannot use any form of TF-M with MCUBoot on the nrf53 or nrf91...
Hi,
I am currently using the NVS library with the nRF9160 and an external SPI-NOR flash device (MX25R6435F). I am getting concerned with the NVS library causing issues,...
Following Getting started with current measurements on the nRF9160 I applied the
to a Thingy:91 (disabled SERIAL, NCS-2.0.0). With that I get about 0,190 mA. That value...
Hi,
I would like to use the NRF52840 dongle (PCA10059) to transfer UART over BLE.
It seems there are some examples available that look promising, but after a day of struggling...
I face problem in k_sem_take() i build a nrf3540 board its successfully running in peripheral uart and some sample programs. while debugging peripheral connectionless rx and...
Hello. We manufacture the device on nRF 52840 and use NFC tag emulation to connect to BLE. We produced two batches of printed circuit boards and there were no problems. But...
Greetings,
In the product specification, it is specified to enable E0E1 high drive when using TRACEDATA[0..3] and TRACECLK. ( Pin assignments link )
Is this setting also...
Hi,
I'm working with a nRF9160 and nRF Connect SDK v1.7.0.
It looks like printk() is not outputting to UART, it previously was working when I was using nRF Connect...
Hi,
I am developing a project that uses TF-M to run some functions from a secure partition. The structure of the project is shown below:
├── lib │ ├── ... │ ├── blst.h...
I couldn't debug with Visual Studio Code, so when I reinstalled it, "Welcome", "APPLICATION", and "CONNECTED DEVICES"
only displayed "Loading..". Please tell me how to improve...
