Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am trying to migrate a moderaely complicated nrf5340 app from sdk 1.9.1 to sdk 2.0 and having a few issues with getting the right crypto configuration. Original...
Hello, guys！
I'm currently just starting to work on the nrf9160dk board. I want to try to explore the communication of nrf9160 with external acceleration sensor. First,...
Hi Team,
Is there any blog/tutorial on how to add custom profile (service/characteristics) with ncsv.1.8.0 and nrf52832/33?
I could find a couple of blogs but they were...
Hello everyone, I'm testing the example ble peripheral "UART/Serial Port Emulation over BLE" with SoftDevice S112 nRF5 SDK v17.1.0 . My board is MBN52832DK and i'm using the...
Hi,
in my project I use the nRF52840 microcontroller as the master I2C device.
Sometimes the TWI peripheral SDA line is forced to a low value by the slave device. This...
Hi, I'm developing an application using fds. I merged fds into ble_app_uart and built complete But when program run fds_init() nRF was crashed I called fds_registered before...
I am using NCS 1.7.0 and latest nRF5340 DK
I am trying to update netcore firmware using the process defined here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1...
Hi everyone!
I have a question regarding the audio support on the nRF52833 chip. Is there any support for sending audio ( Low quality compressed audio ) to headset? Or...
Hi everybody.
For a personal project, I need to integrate a flash or a microSD card to store data.
As computation core I want to use nRF52811, but I'm not able to find...
Hi,
I've lost hours to this so grateful for your support!
I have a custom board using Raytac MDBT42Q, which has a 32MHz clock in the module and I'm not using an external...
To whom it ma concern,
we observed Unkwon Resets after Long runtime ; Several Hours.
We use the NRF52840.
After the reset bit 1 in RESETREAS is detected .
BUT investigation...
My project is based on 'ble_app_uart' and I added dfu service..
so there's two custom 128bit uuid in my project..
But before this, I only want to test dfu service mode...
Hi,
We have made an app that gathers GPS coordinates using an external antenna with the thingy91. The problem we have is that we struggle to test the code when we don't...
Hello,
I am using the nRF52840 dongle with the nrf sniffer 4.1 firmware running on it, using Wireshark to read out its results.
This works fine for advertisement packets...
