Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hello, I am following the official tutorial ( academy.nordicsemi.com/.../) to enable DFU over USB function on both nrf5340DK and thingy53. I am using sysbuild for both board...
Hello Nordic Team,
I am working on measuring battery voltage ( 3.7V ) using a voltage divider ( 220KΩ and 100KΩ ) connected to AIN2 on the nRF54L15 DK.
However, I am experiencing...
My device is a peripheral and during bad RF conditions I would sometimes see a BLE_GAP_EVT_CONNECTED event but the central never receives a packet from the peripheral so it...
Hello,
I'm running both central and peripheral roles for BLE on Zephyr, along with UART and some GPIOs.
SDK: 2.6.2
The project includes MCUboot, supporting DFU...
I have a custom board, with nrf5340, nrf7002 on it.
I would like to get the uA levels of power consumption I see other nrf5340 projects talk about (eg here ) when my application...
i have connected usb type(b) to j3 and kept the switch to usb but no advertsing happens and i have also connected external supply 3v to p21 the board is not on . only while...
Using Zephyr in NCS 2.8 on nrf5340/nrf7002 wifi combo, and trying to get https to work. I'm using the option where the TLS setup is done in the socket layer (enabled in prj...
I’m trying to set up a simple relay using an nRF52840 board to route data between a BLE central (my phone) and a 9600bps UART device. My goal is to send data from the phone...
i've captured the following using a joulescope js-220 as an inline current meter across the VDDM CURRENT MEASURE jumper on my rRF54-DK board....
i'm running the system_off...
Hi!
I'm storing a key in the KMU for use by the ECB.
If I set the slot's destination address to an address in RAM, the KMU pushes the key there correctly, but if I instead...
Hi,
I have a custom board, i enable the adc peripheral, and it generates:
then i connect the AIN4 channel and it generates:
but when i build i get the following...
Hi, I'm looking to develop an out-of-tree driver for the SIM800L modem. The reason I want to develop it out of tree is that I don't believe have the skills or resources to...
HI
I previously disabled DCDC in the app using the following method:
in app.overlay
I am using ncs 2.9.0 I saw some posts using CONFIG_ENABLE_DC_DC=n , but I am unable...
Hi,
I'm try to set up a UDP server on a nRF9151dk, and send data from a remote pc to the devkit. I have tested my sim and networking works correctly, I am able to use coap_client...
