Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I've seen this discussed a few times before, but haven't seen a great answer on this. It seems to be commonly known that attaching a debugger while using the IEEE 802.15.4...
We want to measure latency and PER between two OpenThread Nodes exposed to WiFi interference. Multiple Raspberry PIs, which are configured as AP and/or client, simulate flooded...
Hi,
I have been trying to get Periodic Parent Search active on my nRF54L15DK (and also on an nRF52840DK) without success. My approach has been:
Use the OpenThread CLI...
We are currently using the STM32WL5MOC module and are facing a serious issue with LoRa range. The communication range is not going beyond 1 meter, and the RSSI while receiving...
Greetings,
I have set up some tests using the ZTest environment based on the test sample in ..\v3.0.2\zephyr\tests\bluetooth\adv\. for my custom project which has custom...
Hi,
We are considering using nRF54L15 / SDK3.1.1 -> as a wearable device that is part of a Thread network. We also need to do sporadic BLE connections and channel sounding...
We've a nRF9151 DK for which we built the Nordic Semiconductor LwM2M Client sample using SDK 3.0.2 (modem firmware 2.0.2).
We followed all steps listed in https://docs.nordicsemi...
We are seeing network issues in some particular locations. In these areas, the device is unable to connect to the cloud.
Hardware: nRF9160-based board
Modem firmware...
I am running the boot loader with the default name 'DfuTarg' on a Nordic NRF52840 board very similar to the PA10056. I download this boot loader to the board, connect to it...
I am working with a product that uses the NRF52840 MCU and operates as a BLE peripheral.
I would like to know if the Cortex M4 in the NRF 52840 has support for programmable...
I am using VS Code to develop on the nRF52832, which is externally connected to a TCAN4550 CAN-FD chip. I successfully used the tcan4550evm.overlay to send and receive 8-byte...
Hello Nordic Support,
I am trying to use the nRF5340 SDK to communicate directly with the network core via HCI commands , without going through the application core.
Steps...
We want to use the NRF52810-QFAA-E-R7 in our device. Its only function will be tunneling data from UART to Bluetooth and back. No other functions are needed. What is the minimal...
Hi guys, I am trying to enable timer interrupt in nRF54L15.
but when i debug the application it locks inside the IRQ_lock.
can anyone explain me the issue here. It would...
Hi Nordic Support Team,
I am currently working on integrating the MAX30001 ECG/Bio-impedance sensor with the Ezurio nRF54L15U DK (nRF54L series). I am using the nRF Connect...
