Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
In my project, I need to set REGOUT0 to 4 , to achieve a VDD of 3 volts. In zephyr/boards/arm/nrf52840dongle_nrf52840/board.c there is an example showing how to do this in...
Hi,
I was about to program my nrf52840 with minor changes in the dts and after that I cannot flash any other images to the device. This is what I get when I flash the...
Hi~ I have a new NRF52833REV3 xxAA board, and I need to read its SRAM. However, when I use the JLink command to read it, I get 524288 bits 0. I have tried recover and erase...
Hello,
I am planning on using a 0201 15nH shielded inductor instead of the 0402-size listed on the schematic for the nRF52832.
Here's the link to the component: LMCI0201...
Hi Nordic,
We are now creating a BLE central device which can connect to an BLE peripheral device for some telemetry purpose.
To address privacy concern, the BLE peripheral...
Hello,
I have a workspace project that currently builds fine, however I am starting some new smaller projects and wish to build them as Freestanding so that I can have them...
Code snippet below produces the error code 0x00000001 during nrfx_spim_xfer:
The same SW in a different project does not produce the error. The error occurs during attempted...
Hello,
I have a project of a device with 2 endpoint plus the GP endpoint (242). It's a coordinator.
at first startup, the green power endpoint doesn't appear in the response...
Dear Nordic,
I'm trying to use the LTE Link Monitor and the Trace Collector V2 at the same time in order to collect trace messages from an nRF9160 DK. However, the RAW and...
Hello all,
I am looking for a freelancer to work on a Matter project based on a nRF52840 SoC.
I am an embedded developer and I did already some experiments with the Nordic...
Pretty new to development, compiled and flashed Zephyr basic samples through nrf Connect for VS Code (board type: nrf52840dk_nrf52840) and suddenly board wouldn't respond...
Hello Team Nordic,
We know that %XSYSTEMMODE command is used to set specific LTE mode. I am also using CONFIG_LTE_NETWORK_USE_FALLBACK.
I have a SIM card which connects...
--
I am using Laird's bl654 dongle. If you download a hex file using nrfConnect for Desktop, the dongle is no longer recognized. It works like open bootloader again only...
Hello,
I have been modifying the examples ble_app_uart and ble_app_c_uart to include direction finding. I perform the connection via scan and advertising and then establish...
