nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Dear ,
I am currently using NCS1.8.0.
I noticed that there was warning message as shown below after I downloaded the program to my custom board via my nRF52 dev kit. ...
Board: nRF52833
SoftDevice: s122
SDK version: 17.0.2
I'm trying to log my continuous sensor data from the peripheral on the serial monitor. So I took ble_app_uart_c...
I have a compiling program when using the stock nRF52840dk_nrf52840.dts file, it outputs to the USB port to a serial terminal on a comm port.
As soon as i use my custom...
hello Nordic
i am working with nrf52832, with zephyr, ncs v1.7.1,
the device has a sensor that sample at 26khz each sample is 3 channels of 2 bytes data. the sensor use...
Hi everyone, I'm trying to communicate with OV2640 Camera Module via I2C. I bought this model:
It has SDA and SCL, but doesn't uses I2C Protocol, instead OmniVision uses...
Hi,
In my project, I use SPIM4 to access sd card . It is worked well. Then ,I optimizing power of sd card. The power of my sd card is controlled by LDO.The LDO is enabled...
I'm browsing the Application Event Manager code, and I'm wondering:
I see that struct event_type has (effectively) an array of struct event_subscriber , bounded by pointers...
Hi,
I am using SDK 2.0.0.
I have two problems in this function.
Lets take Vt value as 1420, in one instance.
1. RT2 is calculated as 5076.14. This is incorrect....
I have been trying to implement the IPC code given in to send an event from the network core to the application core. I added CONFIG_NRFX_IPC=y the prj.conf for both cores...
I am working with a board one of my peers designed that hopes to use an NRF9160 for cellular communication (and GPS as well but that's neither here nor there). When setting...
Dear all,
I have pca10059 nrf52480 dongle which I accidentally erased and I could not upload any elf file to run moreover it was not blinking red anymore, no presence in...
my master is outputting all the right signals on the SPI lines. The slave though, although it appears ot recognize the CSN pin and runs the spi_tranceieve function. It does...
Hi
I'm trying to send and receive data with MQTT.
I tried uploading asset trackerV2 bin file and it works fine with nrf cloud.
now I want to use the sample "MQTT_simple...
Hi there,
We have recently acquired some new nrf5340DK's and we suddenly noted that the SYSTEM ON LOW POWER current increased from about 5 uA to about 25 uA.
Attached...
Hello guys
We have a problem with the SPI bus driver on the nRF9160 MCU. In our project, we use SPI1 and SPI3 instances.
When I send a package in some of these SPI busses...
