Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
When I use Windows nRF Connect to connect nRF52832 device. It pop up window for user to enter passkey. But When I use iOS nRF Connect to connect nRF52832 device. It doesn...
I am trying to implement spi in my project and have encountered an issue where the delay from chipselect to sclk is around 10 us which should be as low as 1us according to...
I have been developing my code on NRF52840 based on nrfsdk v1.7. Since keil free version has a limit of 32kb i am moving my code to VS code. VS by default adds 2.0 latest...
Hi,
I'm testing maximum tx throughput.
I'm using ble_app_hrs example and mcu is nRF52832(s132). (sdk : 16.0.0)
The goal is transmit data at 96Kbps.
I read that the...
Dear Members,
We have 2 ANT receivers and 1 ANT Speed Transmitter, (Bicycle Speed Cadence) , Garmin GSC-10,
Is it possible ? Looks like one receiver gets a good value...
Hi,
I am using NCS v2.0.0, VScode with "nrf connect for vscode v2022.7.242".
I can't build any samples with MCUboot, by enable CONFIG_BOOTLOADER_MCUBOOT =y.
The build...
The following error occurs when I plug in the USB cable to burn the firmware，This is an interesting bug: it usually fails on the first burn, but succeeds on the second or...
Hi everyone,
I am new to nRF52833, and trying to learn it with some tutorials. I am following this tutorial.
You can download my "examples" file from here . You should...
Hi,
Can you please provide some sample code for sending data to Tm4C using ble_app_uart in VScode and also tell me which function I need to use for sending some data from...
When I use Windows nRF Connect to connect to nRF52832 device. It pop up window for user to enter passkey. But When I use iOS nRF Connect to connect to nRF52832 device. It...
HI, I am start use NRF52840DK(rev3) to devlopment usb application，but jlink always show this information
I try to use 'nrfjprog --recover' to disable read protection,...
Hello Groups,
I'm trying to send I2C/twi data from nRF52832 using the Nordic development board with nRF Connect SDK 1.9.1.
Based on the sample project ble_app_uart, I...
Hi nordic:
As shown in the figure below, I see that the BLE protocol standard mentions the ScanReq backoff mechanism. Does NORDIC implement it?
jermi.jin
thanks!!...
Hi,
The central_uart sample hardfaults when bt_enable(NULL) is entered. I can use the debugger and step over the first couple lines but stepping over bt_enable causes a...
