I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I am working on DFU-OTA example on BLE. my doubt here is once the controller copied the image into slot1 bootloader will immediately start to validate whether the image...
I am using the following code to generate and output a n-MHz clock on a GPIO pin. (code is borrowed/copied from another question on this forum)
However, the clock output...
I download the zip file(nrf-command-line-tools-10.15.4_amd64.zip) in the website.
And then I unzip it get the following structure files:
JLink_Linux_V758b_x86_64.deb JLink_Linux_V758b_x86_64...
Hello everyone!
Long story short, we are developing a BLE application based on the Nordic UART peripheral example. The board (STM32 micro + BL652 BLE module w nrf52832 inside...
Hi All,
I have a question about notify data size.
I have a 10byte array, but the length after Notify is sent will be max len = 50byte which I set in characteristic.
...
6 hours ago
Online steve.hou
2 pts.
Dear support,
I am the beginner of of the Nordic with 52840 chipset, i am try to running sdk 1.90 with zephyr os
i am...
Hey, I'm trying to get a basic BLE with coded PHY (125Kbps) setup with on the fly encryption/decryption working but I'm running into a strange problem. I'm using a custom...
Hi, I want to use the nRF9160 in a project, where I need the antenna attached to the nRF9160 to be able to handle being 1000m below the sea-surface. It is an AUV that collects...
Hello,
At present, there is a problem. When there are a few broadcasting devices nearby but many active scanning devices that the active scanning is not easy to find devices...
Hi
I am using app_timer_cnt_get() like MIllis()
uint32_t millis() { uint32_t milli; milli = app_timer_cnt_get() /32.768; return milli; }
but when i connect the nrf52840...
Hello ,
i have successfully compile and run 'binky' and 'Hello_words ' sample code using segger .Now i want to test Uart communication with nrf9160 . (want to send string...
Hi,
we are following below link for DFU example i.e. serial dfu on nRF52833. we are not able to install mcumgr in windows . are we missing anything here. kindly help us...
I'm testing an implementation of the serial UART bootloader for DFU. Firmware update using nrfutil works fine, using a serial-USB dongle, The only issue I'm seeing is that...
