Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi! We're working with a gateway comprised of a workstation running RHEL 8.5, a Bluetooth USB dongle with a nRF52840 chip running the connectivity_4.1.2_usb_with_s132_5.1...
Hello everyone,
i know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet. I want to flash a custom board...
Dear Nordic Team !
I think I found a bug in the ble_db_discovery module of Nordic SDK 15.3.0, maybe other SDKs are affected too. I am implementing a BLE central device for...
I received my NRF52840-DK board, today, from Digi-key. I followed directions in starting it up - power set to USB, switch to on. When I turn it on, all LEDs flash and pressing...
After a lot of stumbling around (the documentation for the ANT+ examples needs to be improved) I finally got some of the ANT+ examples working on my nRF52 DK board. When programmed...
HI
How can I to send 512 characters over BLE NUS?
I saw in Ble uart example this
I received 247data from BLE NUS
can I to receive 512?
how can I do that?
...
Hi,
We are currently going through the Verizon self certify program, using an adaptation of the asset_tracker_v2 firmware on our device. Verizon said to reach out to Nordic...
Look like a hard coded bug in API generated in build\zephyr\include\generated\syscalls\flash.h ?
-- Found BOARD.dts: zephyr/boards/arm/nrf52840dk_nrf52840/nrf52840dk_nrf52840...
Hello! I have a serial device (RN8209 power meter) which is connected by UART to a nRF52832 with 4800 Baud. I am using SDK17 nrfx UARTE to access it, but I have observed,...
We have a custom board with a uBlox Nina-B1 module. Pin 0.05 is connected to an analog switch (NX3DV2567) which powers a microphone and capacitive switch. When the pin is...
Hi everyone,
I am using nrfConnect 3.9.3, And SDK v1.7.0.
I am working on a project based on uart example.
My question is if there are some way for clean/discard all...
I'm unable to get a cloud response using the XPING command with some IoT sim cards on the nRF9160. I've been working with serial_lte_modem projects on this chipset. I've also...
I cannot find any information on how to update mcuboot over SMP when using the immutable bootloader.
I have my NRF52840 setup with the chained bootloader: b0 -> mcuboot...
Hi,
First of all thank you for your support and suggestions.
As I am planning to use nRF52840 SoC in my design, (Project: BLE based Environmental sensor). The circuit...
