I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I have an Zephyr application on the nRF5340 that I've been working on. I can debug fine in SES without a boot loader. However, when I add MCUBoot into the mix then everything...
I have some code that runs on the application and network processors that uses NRF_RPC NRF_RPC_CBOR (similar to the entropy_nrf53 sample) to communicate during boot loading...
I'm trying to get setup to debug an application that uses both the app and net cores. For now I'm using the example nrf/samples/nrf_rpc/entropy_nrf53/cpunet. I'm trying: ...
I am migrating our mesh network stack to NRF 52840, which is based on 802.15.4.
I would like the code to be more efficient state machine so that I don't have to busy-wait...
Hi,
I am using the ble_blinky example as a template to develop my project, with nRF52832 and SDK 17.0.2.
My first goal is to reduce consumption, so I have changed the...
Hello,
i had a look at lwm2m_client_sample and it worked pretty well. Now my next step is to be able to send for example a 100 or 500 Bytes Payload from nRf9160 to Leshan...
Hi Karl,
Sorry, I inadvertently closed the issue.
In my understanding, with SW9 in position "VDD", VDD_nRF is about equal to VDD_HV, so the measurement should work. I...
Hi
Is there an example for BLE "Just Works" using the NRF Connect SDK for the peripheral device?
I am using a peripheral device without display and would like to allow...
Hi,
In our application we use a motor. In the case that the watchdog would trigger while the motor is running, we need to stop the motor. For this we need to set the PWM...
Hi, all,
At first, I have to say I am a newbie in programming for BLE. ^^"
I trying to development a cycling power meter, so I want to modify this CSCS example to...
Hello, Recently I tested and flashed the Zephyr program to the nrf52840DK, it works fine. While I flashed as usual last time, I saw the LED5 flashing and then the PC didn...
I would like to perform a OTA DFU in a nRF52840 DK using nrfutil. For that, I'm using the example that is in SDK/examples/dfu/secure_bootloader/pca10056_s140_ble in the target...
Hi
I have follows the following steps.
1) I build 'hci_uart' sample for nRF5340DK successfully by following guide https://docs.zephyrproject.org/latest/samples/bluetooth...
Hi, I tried the fourth step of this guide https://openthread.io/codelabs/openthread-hardware#3 , but if I start the OpenThread daemon, I got this output that is not the same...
