Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi, i have two boards with me i.e. nrf52840DK and nrf9160DK. I want to debug nrf52840DK using nrf9160DK, I don't want to use onboard jlink on nrf52840Dk, is it possible to...
Hi! I'm currently using
- board: nRF52840 DK
- SoftDevice v15
- ble_app_template example + midi (adding custom service and characteristic) -------------------------...
Hi,
I used SDK 16. softdevice: S140 v7.01. And set APP_USBD_VID and APP_USBD_PID to 0 at sdk_config.h
I follow this post of https://devzone.nordicsemi.com/f/nordic-q-a...
I'm trying to have nRF9160 DK communicate with an external accelerometer.
nRF9160 stop working at the function of i2c_reg_read_byte in the code below.
Does anybody give...
Dear fellow developers
I would like to integrate a smart lock ( danalock v3 ) with the alarm system, so that I can control the lock via the alarm system. The alarm provides...
Hello,
I have a few questions regarding power consumption of the BLE modules
With regards to the nRF52810:
The data sheet lists the following as specifications for...
Is there a quick way to disable MCU Boot on the Thingy91 Asset Tracker example? I need to use the button on the device to my applicaton, and it is neccecary that the user...
Dear Sirs, good afternoon
I am using a (PPK + nrf52840 DK) to measure current on an external device.
Is it necessary to cut the SB40/41 jumpers in this case?
Thanks...
Dear Nordic ：
I want FTMP (Fitness Machine Profile) to be supported in my product (A smart trainer uses NRF52832, called Gravat in Ant+ official website).
I find that...
I want to monitor the RTC count and generate an interrupt when a specific count is reached. And without stopping the RTC, I want to generate an interrupt again when the next...
Hi
We have the issue that GPS has no fix.(board: Thingy91 version: 1.0.2) I used the pre-compiled hex thingy91_ltem_dfu_2020-04-29_bc7ade8b.hex downloaded from Nordicsemi...
i want to connect Nordic thingy to a nrf 52840 soc with ble central example.
all i want to get is thingy environment service and get temperature and humidity values on...
Hello,
I got the acceleration value using mpu6050 sensor. And I am going to use this to get the angle of the sensor. The formula below has shown that angles can be obtained...
