Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
ATT MTU THROUGHTPUT EXAMPLE FOR nRF52810 on KEIL using S132 v5.1.0 PLEASE >>>>>>>>>>>>>
Tried this : https://devzone.nordicsemi.com/b/blog/posts/the-s132-v5-1-0-is-now...
Hi!
I am currently developing product containing Thread mesh and BLE peripheral service. I am using Thread SDK v2 in my software. My application has to support writing to...
Is there any NRF51822 DFU guide under following conditions:
a. NRF51822
b. SDK11.0.0
c. Dual Bank BLE DFU(\examples\dfu\bootloader\pca10028\dual_bank_ble_s130\)
I...
Hello i am working with light switch proxy client server sdk example.i make provision light and switch using nrf mesh application.i have three nrf52832 dk board.i flashed...
Hi.
I work with PCA10040 and SKD_14.2.
I use UARTE with easy DMA. I see big enough delay between sending nrf_drv_uart_rx_abort and entering to UART event hanler. What...
I tried to create a descriptor for a characteristic. I modified the app_blinky and added a ble_add_descr_params_t variable. After The Initialisation and definition of the...
Hi,
I've tried blink,hid,uart,template similar sdk examples so far. Now i acquired some experience about nrf52832 processor and bluetooth,but ii don't really have enough...
I have had an issue recently with some beacons that I am using to log temperature data. A portion of the beacons drained their batteries very quickly and didn't respond to...
Hi I have this piece of code which works in SDK 12 but when I port it to SDK 15 the sd_ble_gatts_characteristic_add function would fail with an error code of 7. No change...
Hi,
I want to put my nrf52832 into the low-power mode. I select SYSTEM ON with low-power (instead of SYSTEM OFF) in order to overcome reset. In order to do it I call sd_app_evt_wait...
Dear nordic team
I am using SEGGER EMBEDDED STUDIO and nrf52840 DK. I want to add some pwm nrf_drivers like nrf_nvic.c , nrf_soc.c , nrfx_pwm.c to my project. when i added...
Hello,
I started off with two nRF52832 Dev Kits, and have customized the UART Central - Peripheral example to send an array data from Peripheral to Central (no uart simulation...
A month ago I bought an nRF52840 DK to start creating my own projects with the nRF52840 chip
I have created a new project in Segger Embedded Studio for the nRF52840 DK....
Hi,
is it possible to use the nRF52 dev kit and/or the nRF52 Dongle (nRF52840 Dongle) wiith the dongle firmware without nRFConnect?
Background:
We want to use a nRF52...
