Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello,
You've previously provided the sourcecode for nrfutil, before it was rewritten here https://github.com/NordicSemiconductor/pc-nrfutil .
Is it possible you could...
I am developing a FW for the nrf54l15 which should log sensor data into its internal flash (RRAM) and make it read able later from a Smartphone via BLE.
For this scenario...
Hello everyone,
We hope this message finds you well. We'd really appreciate some guidance on an issue we've been encountering in the field.
We have deployed several hundred...
I am dealing with a HardFault occuring in my code, and I am unable to trace the error. The output when the HardFault occurs is <error> hardfault: HARD FAULT at 0xD0D0D02A...
Hello,
I am using the Nordic Thingy:53 and trying to collect sensor data using Edge Impulse.
I was able to successfully connect the Thingy:53 to Edge Impulse and stream...
The device i am currently developing is a battery powered dongle with internal power supply unit for battery charging. I am using nrf5340 USB pins D+ and D- for communication...
HI, i have been using the nrf9151 to download my OTA's it has been working fine, but since this week it stopped working for all device we have deployed, i suspect it is related...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
I have a fresh clone of Zephyr version v3.4.0-rc1-66-g462dc9746b42. I want to build and debug the unmodified project samples/tfm_integration/tfm_secure_partition.
...
Hi
I want to add the nordic documentation as an MCP server to claude and gemini clis. But this seems to require authentification by Kaipa, which is a paid service ?
...
Hey Team,
Whenever we flash the audio application (from the official samples provided) on a development board and leave the board unpowered/unattended for 10-15 days, the...
What is the correct way to connect an nPM1304EK (or other nPM product) to an nRF7002DK? Is it possible to do this and power the nRF7002DK via the PMIC but have the USB connected...
When trying to figure out why we couldn't flash the network core on the nRF5340 with pyOCD, we noticed that the Debug Base Address of the AHB_AP returns 0xe00fe002 for the...
I am trying to migrate my project (for a custom nrf5340/nrf7002 board) from NCS2.9.0 to NCS 3.1.1, to hopefully get the wifi WPA Enterprise functionality to work.
This is...
I can connect to targets using the JLink WiFi probe and JLink Commander (JLinkExe), but when running `nrfutil device list`, they don't show up there. Can you please patch...
