nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
nRF54L15, Zephyr +MCUboot. I am unable to redirect LOG_INF() output to RTT.
prj.conf
Can you tell me what is wrong? How to force logger to output to RTT?
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
We are trying to pass interrupts at high speed (clock signal) running at 800khz from port p1 to signal the RISC-V Co-processor to trigger a capture on a 4 bit bus. Is it possible...
Hi,
using nrf connect sdk 3.11, nrf54L15-PDK
I am testing low power with development board, I am trying to reach low power 2.9uA as bench marked.
When GPIO (button)...
I noticed in SD7 SDK16.0.0 when CENTRAL and PERIPHERAL connections are defined, the soft device will return designated central and peripheral connection handles. For example...
Hi,
We are modifying our existing product and adding PA to increase the range. Device right now is developed with nrf5 SDK, but we have plans to move to NCS. However manufacturer...
hi support team,
customer is using our 54L15 for mesh lighting project, here are three questions:
1.
customer needs timer model, i see the "time_cli.c" and "time_svr...
I'm developing for a custom board that has an nRF52832 and an FM25W04 external flash. My application uses nRF Connect SDK v2.9.2. I have a debug build that doesn't use a bootloader...
Gemini gave me some code to help get the phy when a connection is updated which does compile but there is an error warning in vs code. Here is the code:
here is the error...
We are evaluating the nrf54 series chips for a new product. We currently have a product that uses the nrf52 series and the distance measurement library. I see that the nrf54...
Hello,
I'm using nRF52840 with Softdevice S140 7.0.1 and SDK 16 for my BLE application in which I send data via notifications. I'm interested in tracking the hvn_tx_queue...
Hi everybody, I have some problems with flashing my custom PCB with an nRF52832. I saw online that you can flash the nRF52832 using the nRF52840 DK. I have looked into a lot...
Dear Support Team, I have downloaded the latest version of VS Code;
I have also installed the latest version of the nRF Connect for VS Code Extension Pack;
The J-Link...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
We are not using the NRF5340DK board. According to tests, after initiating an SPI data exchange, the program is delayed in executing the next CS pull-high operation, resulting...
