Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
To tell a central device to refresh the service list, I have enabled NRF_SDH_BLE_SERVICE_CHANGED. However, when I do this all/most of my existing custom characteristics start...
Hello,
I am trying to port ble_app_hrs_rscs_relay example to nRF52811 with softdevice s140 7.2 and nRF5_SDK_17.1.0. Everything works fine and the app is running and I can...
Hello,
In the Zigbee Network Coordinator example when flashing new file to nrf52840-DK the Zigbee network steering automatically starts. How do I disable auto-start of network...
I have allocated 100 pages for FDS, but now i dont have enough space for the DFU. ir there a way to use FDS space (im happy to loose data stored in FDS), for the BLE DFU?...
Hi,
Is it possible to send data on Connected mode and in parallel also send the periodic data ?
I tried to implement that but it fails to send in data on Connected...
Hi,
I work on a project that uses the dfu target library for firmware updates. This has been working flawless until I added task watchdogs.
The problem that I see is that...
Hi,
I am using a ISP3010 SiP which inludes a nrf52832, a DW1000 and the corresponding antennas (built-in antenna).
I have a custom board (board1) as reference, where the...
I added custom data to default asset_tracker_v2. The custom data is properly encoded and displayed in JSON format in LTE and acknowledged by Azure IOT, but it seems that the...
Hello,
We're working with nRF52833 & nRF52840 and I'm trying to figure out why we've ~0.3ms IRQ Latency from the moment I call the function " uart_irq_tx_enable (dev );...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
Hi,
My customer use nRF52840 with nRF5 SDK 15.0.0.
They have come up against the difficulty that uart RX pin instability.
I have searched the DevZone and it's advised...
Hi Nordic Community
I have been building a thermometer device from which I would like to send temperature values via periodic advertising.
I have based the sender and...
HI
I am beginner, I have a question , is necessary to put both crystal in circuit configuration?,
in my application i am using nrf_calendar example like a watch, may be...
Team,
I am using nrf52810, sdk 17, sd112.
I have setup a write characteristics, to receive some long data ( 64 bytes)
// write char memset(&add_char_params, 0, sizeof...
I added ring buffer and UART ASYNCH interface to asset_tracke_v2. I added CONFIG_RING_BUFFER = y, CONFIG_SERIAL = y and CONFIG_UART_ASYC_API = y to prj.conf file. The build...
