Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
I am making an application based on the peripheral-nus example. The checking for CR is removed and all characters are just sent further when available. The problem is...
Hi, I have developed a stable program on the nRF52840 board, and now I'm transporting all the code, and trying to make it compatible with an nRF54L15 board.
I used ZMS to...
Howdy,
I am currently working on the nRF52840 chip and trying to convert my SPIS code from being in my main while loop into being interrupt driven. I am using Zephyr to...
Hi!
I want to integrate power management into our FW. Therefor I did enable it in the prj.conf:
And added runtime enable and action run calls regarding this device...
Hi,
Is there a sample demonstrating the EasyDMA configuration for the I2C21 peripheral of the nRF54L15 using SDK 2.8? I found a sample for the nRF52 with an earlier SDK...
HI,
I am super confused about which direction to go forward...
I need example code and tool chain where I can build a
1) ble bootloader that supports the Nordic Semi...
Hi,
We are using nRF52832 custom board for our application.
In this board we have to use P0.05 pin as GPIO Input. But it is continuously showing LOW signal in multimeter...
Hi,
I have installed nrfutil on my Windows 10 computer and get the following error when running it:
C:\Users\00315055>nrfutil --help Traceback (most recent call last)...
Hi,
I've just completed Ex 2 of Lesson2 in the BLE Fundamentals course on the DevAcademy and have noticed a couple of problems. Firstly, the nrfConnect app for iOS seems...
NCS v2.9.0
nRF52832 DK
peripheral_uart sample
"Online Power Profiler for Bluetooth LE"
has a BLE role to send non-connectable, non-scannable packet,
I want...
The Application create connection as Central with the following parameters:
After connection established, the application execute the following Subrate request command...
Dear Sir.
I wonder on the noise demand on the power supply to nRF54Lxx? I have 24Vdc from a battery, and would like to use a standard DC/DC converter down to 3.3V (e.g LT1933ES6...
Hi NORDIC Support Team,
I am using the nrf5340 and attempting to enable a BLE connection on the board with 2 clients simultaneously.
The issue I'm encountering is that...
Hi Nordic
Our customer is going to develop LE Audio porduct and have some question of firmware as below:
(1) Need to use I2S only CODEC (DAC) (2) Currently using the sample...
