I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
I am want to do wake up on motion when any threshold value generated by icm 20948 accelerometer I want to send an interrupt from icm 20948 to nrf52832 to wake up from...
Hi !
I'm using the nrf52832 with SDK 11 as pheripheral.
In Android phone the bonding and the scan request working great with my unit !
However, in IOS
1) i do scan...
Hello,
I am working with LPN example of SDK 3.1.0. In the example I need to change the poll interval time based on our application requirement.
I looked at this equation...
Hi Nordic team,
I have a curious problem I need a little help with:
(NRF52840 & SDK 15.3)
I have a project which is an integration of the ble_uart example and the serial_uartes...
I have searched your forum and have found several references to my issue; however, I have not been able to get anything resolved.
I am using the nRF51822 which is part of...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I have gone through “Application Timer” tutorial...
I have a development board and load the client central BLE blinky to it, then the peripheral BLE blinky to my custom board and power up and the central development board stays...
I was wondering if it is possible to do HTTP requests with the nRF9160 just by using AT commands? Since this is usually possible with such kind of modules.
The reason is...
Hello everyone,
I've got a three type of devices: 1 Central device, 2 Peripherial devices, and mulitple beacons. Central is connected with two peripherial devices with...
Hi Devzone,
We are using the nRF52 DK in a prototype which is under stress, and we noticed that any bending of the board breaks the BLE connection.
To easily replicate...
Hello,
I am currently writing a script whose purpose is to automatically provision and configure devices.
My question is related to the devkey_handle and address_handle...
With SDK 14.2.0 and S332 softdevice, I'm using UART to control ESP8266 WiFi module with AT commands and I'd like to replace app_uart (+FIFO) with nrf_serial , in order to...
Hi,
I am setting OOB with sd_ble_gap_auth_key_reply() method { 0x11, 0x11, etc 16 bytes }, but when trying to connect with desktop nRF Connect there is an error 132 inside...
Hi,
I am getting errors when attempting to include the nvs library to save data to flash storage on the nRF9160 DK. My CMakeLists.txt:
I get the same errors with or...
Hi,
We tried to use a smartSIM from Sierra Wireless with the nrf9160DK without success.
The nrf91 can connect to the LTE network after a few minutes (LED4 steady). However...
