Hello,
I am experiencing an issue with my nRF52 DK. The target nRF52832 appears to be working, but the on-board debugger is not functioning.
Symptoms:
No power/debug...
I have two nRF9151 DKs and want to evaluate direct, SIM-free DECT NR+ communication using FT and PT roles. Please help me with:
- DECT NR+ MAC/PHY modem firmware, rather...
I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hi every one , i tries to call the generic_onoff_client_set function to send a message from the client to the server but this ain't working. Can someone please help me?
...
Dear Forum,
I am looking for an OAM vendor offering a small keypad / pinpad device running on an nRF52 SoC. Should be powered by a rechargeable battery and have mini USB...
Hello.
I want to use the nrf52840 as Bluetooth radio controller which is connected over UART to Linux based ARM host.
We are targetting to use meshctl on linux host...
Hi ,
We are facing a problem with cellular connection in NB-IOT mode on NRF9160. We are trying with the asset tracker sample , but cellular connection does not happen. Can...
Hello Everyone,
I started to use the NRF52832 recently and wanted to use it with a sensor from Melexis called MLX90632. I am using sdk 15.0.0.
This sensor have a library...
Hello,
Currently I would like to add a functionality to Bluetooth Low Energy App (BLE). I have a bluetooth slave device that require a specific sequence of sending string...
So, i have been trying to perform a DFU over serial using the method mentioned here by Hung Bui.
Here is a summary of what i did:
- build and flash mcuboot
- build and...
I am using pc-nrfutil to perform FW upgrade (transport is serial), The target is custom board with 52840 processor, running Bootloader adapted from the SDK.
For most of...
I've configured the SPI with DMA module as in the code below.
I've loaded the tx buffer with sample data and start the transaction; however, I'm not reading anything either...
Hello,
I have been working on porting the BLE UART PHY S erialization to the STM32L476 (with a Nordic NRF52832 Dev Board and STM32L476 Nucleo-64). I have read the porting...
Dear Nordic,
Running BLE mesh sensor network with multiple servers and a single client linked to a gateway.
SDK: 16.0.0_98a08e2
SDK Mesh: v4.0.0
nRF52840
The client...
I'm attempting to using pa_lna_setup(), specifically the softdevice function sd_ble_opt_set to enable/disable the radio and an external amplifier. My application is a custom...
Hi Team,
We are using the uECC library for ECC Functionalities, while connecting the debugger we are getting the pop up message like "not finding the source file".But while...
Hello guys,
I have nRF9160DK board here with me and the nRF Connect SDK v1.3.0 environment installed. I want to connect to AWS IoT Thing through the MQTT connection.
I...
When I was testing USB on SDK16.0 with nrf52840, the gateway acted as the host, the following scenario 1 worked abnormally, and scenario 2 worked normally.
Scenario 1: When...
