Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
Hi all,
I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
i am trying to run advertising.py from pc-ble-driver-py .
i am keep getting exception from
except IndexError : raise NordicSemiException( 'board not found' ) is there...
I am looking through the BLE examples, but I can't seem to find an example that best fits my project scope where I wish to have a BLE central service that reads data from...
Hello Nordic support team I want to send command from hm10 ble chip to Nrf52832 dk board.So before I start to implement this I want to know that HM10 ble chip can communicate...
Hi, all.
I want data read from gyro sensor through i2c, and then send it through bluetooth equipment.(PC or iPhone and so on)
But i don'k know how to send gyro sensor...
I am asking about using the sd_rand_application_vector_get function; it seems that it causes my board to crash, and it never returns a success code.
I have already seen...
Hello:
I am upgrading my application to use Mesh SDK 3.0.0 (I was at 2.1.1). In my application, I process the mesh from the main loop (per the instruction in the Interrupt...
Hello All, I would like to implement tracking over MESH network using nRF52840. 1. In my MESH network, there are some devices who continuously advertising (say beacon). 2...
HI.
I am following the document http://infocenter.nordicsemi.com/pdf/nRFConnect_BLE_User_Guide_v2.2.pdf to work with nRFConnect desktop App and my DK BMD300(Rigado). ...
Hello,
I'm trying to play voice using PWM in nRF51822.
I've already experienced this using other MCU before.
So. I'm trying.
Voice source data is 8bit / 8K / mono...
Hi,
I am working on nrf52832 , SDK15 and softdevice S132. I am modifying the ble_app_hrs example code in SDK
I was trying to implement a whitelist with the address of...
I am using ble_app_uart SDK_11 s130 on nRF51-dk. I would like to make the device running on ble_app_uart connectable but not discoverable. The Android app will have pre-knowledge...
I am using nRF52840 with sdk 15.0 version. I am able to read OR write data into flash using fds library. But now i want to write one or two bytes into flash and read this...
Development Kit - nrf52
SDK Version - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Setup : I am trying to interface an E Paper Display...
