Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
nRF5 SDK structure project use makefile and sdk_config.h header file, When I want to add a component to my project. There is too hard work to modify the makefile and sdk_config...
Hi everyone,
I am trying to understand this sample code: here
But I don't understand how to choose an arbitrary pin for the LED.
And also, in LED_MASK which pin is...
Hi,
I recently dug into the potentials of the NB-IOT network allowing iot devices to directly make use of cellular communication. With the release of the new nrf9160 containing...
Hi,
Recently, I was trying to pair the nRF51822 development board by windows swift pairing.
While I turn on the swift pairing function, I still cannot use this feature...
I have a similar question to https://devzone.nordicsemi.com/f/nordic-q-a/32115/how-to-parse-the-log-file-of-the-nrf-connect-for-desktop
There are lots of data in these log...
Hello.
Recently, our supplier recommend us to use nRF52810 instead of nRF52832.
These two MCU have same pin map, so just we pulled off existing nRF52832 from the board...
Hi,
we had used nRF52810 in our product. Our product is undergoing FCC & IC certification.
FCC & IC regulatory body had requested to provide Tune UP tolerance values of...
Hi There,
I was trying to understand the step to create a test app for dfu bootloader update via BLE for PCA10040. Below is the documentation I read.
http://infocenter...
Good day
My nRF51822 uses the Eddystone example with SDK 12.3.0 in conjunction with S130. When I configure TLM in slot 1, I notice that the temperature is about 6.5 degrees...
Installed nRF5_SDK_15.2.0_9412b96 and nRFGo Studio. nRFGo Studio fails to recognize the nRF52840 DK board. Screen like this:
It sees and correctly identifies the Segger...
I am trying to do things like
get the current date and/or time
configure a socket
activate a socket
Usually I use commands like
at+cclk
at+csdf
at+ctzu...
I am following the Thingy:52 "Compiling With Keil" instructions provided in the following link.
nordicsemiconductor.github.io/.../firmware_compile.html
However, I get...
Hi,
We have released multiple products with the NRF52832 chip with SDK's ranging from 10.x to 14.x, quite successful so far.
However, one part that is lacking in my opinion...
I have been struggling with getting nrfjprog working on CentOS 7.x. Each invocation results in the following error due to the version of glibc used to link the nrfjprog binary...
