I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hello.
We have a working DFU system using Nordic's Secure Buttonless DFU bootloader. The bootloader correctly checks if the incoming DFU package has the correct 'init packet...
Hi all,
I am curious about the storage capabilities of the Nordic Thingy. I would like to store information about the received messages like a timestamp. How much data can...
So, here is an interesting and fun one: I am using a module with the nRF52832 to control an LED driver with a PWM, we
According to the documentation http://infocenter...
I am starting to use FDS for saving data to flash memory. In the "flash_fds" example the macro APP_ERROR_CHECK() is used to check for errors in most of the function calls...
Hello,
I tried to send data through the proprietary radio. My devices are NRF52832. The data I would like to send is an uint8_t array:
Right before I send it out, I...
Hi everyone,
My English skill is not good, but I really want to share this problem to all developers that I spent three hours for it.
Example nRF5_SDK_for_Thread_and_Zigbee_2...
Hi!
I have questions for Nordic developers team. What capacity of network is possible with nrf52840 thread mesh? I've tried to attach large amount of nodes to mesh and...
Hi Guys,
I want to use the TWI for my mesh application in which I want to read out 2 sensors (Sensirion SHTW2 and SGCP3) and then send the sensor values over a mesh network...
Hi all,
I´m using nrf52832 with sdk 14.2.0 and softdevice s332.
I have opened and closed the eclipse. Now when I open it, it compiled and gives me this error that I did...
Hi,
I am using nRF_SDK_15.0.0?a53641 and writing a program with keil.
I am trying to read data from the acceleration sensor( LSM303DLHC ) by communication with BLENanov2...
Hello
I just started learning nrf52832 DK and run few of the examples. I wanted to start developing my own application based on the examples. Right now, I want to read...
Hello, I have some confusion about updating advertising packet dynamically.
I am using nrf52832 with SDK v12.3.0. I am sending datas from sensor in advertising packet(manuf...
Hi,
I am trying to build the ble_connectivity code "ble_connectivity/pca10040/ser_s132_uart" to test the serialization part. The scan is not working. I am using PCA10040...
18.9.13 RAM[0].POWERSET (and sections associated for other RAM sections) states:
When read, this register will return the value of the POWER register.
however the...
Dear Sir,
I was using my Rigado BMD 300 and it was working fine.
When I open the nRFGo Studio the following was the details displayed in the tool.
But sometime after...
