Blog

After an nRF5340 executes a power-on, brown-out, watchdog timer, or pin reset it is not automatically accessible to debug probes. This is true even if the nRF5340's memory is completely blank --i.e. no settings have been written to the device to disa...

This blog post provides step-by-step instruction on running Door Lock example from the CHIP repository. It demonstrates how with help of the mobile phone, commission accessory to the network using Bluetooth LE, and remotely control a door lock device...

Hello everyone, 5 years ago, FruityMesh was open sourced as the first connection-based Bluetooth Low Energy mesh network based on the nRF52 series. Now, after constant development at our Mway headquarter in Stuttgart, we are proud to announce F...

The nRF9160 is an exciting addition to Nordic's lineup of processors and radios. Ever since the announcement of a Nordic cellular product, I was chomping at the bit to dive in. And boy, did I get that opportunity! In this post, I'll break down some o...

Introduction The pairing-based cryptography (PBC) differs considerably from the prior cryptosystems. It covers many novel cryptographic applications that are hard, if not impossible to construct with other known cryptographic primitives. The PBC...

Check out the other versions of this tutorial: nRF Connect SDK Tutorial series - Part 0 | NCS v1.3.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1.4.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0 This tutorial series will cover the ba...

→ Check out the preceding part of this tutorial series before starting on this: nRF Connect SDK Tutorial - Part 2 This is the third and last part of this tutorial series and will go through some important aspects that haven't...

→ Check out the preceding part of this tutorial series before starting on this: nRF Connect SDK Tutorial - Part 1 Welcome to the second part of this tutorial series. Now you know, to a small extent, how samples are built using NC...

→ Check out the preceding part of this tutorial series before starting on this: nRF Connect SDK Tutorial series - Part 0 This part of the NCS Tutorial series will be short and concise and will get you up and running with NCS and ...

Check out the other versions of this tutorial: nRF Connect SDK Tutorial series - Part 0 | NCS v1.2.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1.4.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0 This tutorial series will cover the ba...

Introduction Machine learning(ML) is a still growing field, and with the TensorFlow Lite port, there is now support for machine learning on microcontrollers. TensorFlow is an end-to-end ML-platform owned by Google. We want to use TensorFlow Lite to i...

For the longest time we’ve had this idea, of turning one of our most-used Swift Collection Types into a simple one-instruction comparison call, down at the assembly level, to check whether an element belongs to or not in a Set-like data structu...

Overview In this blog, you will measure the PSM floor current for the rev. 2 version of the nRF9160 SiP. Requirements Hardware You will need: an nRF9160-DK (the one used here was v1.0.0). Be sure that your version uses rev2 of the nRF9160 SiP (...

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development.  Introduction The nRF52820 IC is a subset of the nRF52833 with smalle...

In this post we describe how we build the ThingyWorld demo for embedded world 2020.

→ Check out the preceding part of this tutorial series before starting on this: nRF Connect SDK Tutorial - Part 2 This is the third and last part of this tutorial series and will go through some important aspects that haven't been cov...

→ Check out the preceding part of this tutorial series before starting on this: nRF Connect SDK Tutorial - Part 1 Welcome to the second part of this tutorial series. Now you know, to a small extent, how samples are built using NCS, an...

We released a small update late last week. It’s a follow-up to our last release of 2019, and like its predecessor, this release, 2.1.2, aims to improve the general stability of nRF Connect for iOS as well as take care of some of those loopholes...

→ Check out the preceding part of this tutorial series before starting on this: nRF Connect SDK Tutorial series - Part 0 This part of the NCS Tutorial series will be short and concise and will get you up and running with NCS and your ...

This blog post contains answers to questions asked during the "Embedded Antennas for IoT" webinar hosted by Nordic Semiconductor 17.10.2019. You can watch a recording of the webinar here. You can download the slides at the bottom of this po...

It has taken a lot longer than we previously thought, but we made it here, to our first big point release for nRF Connect 2.0. Throughout this “two-point-oh" journey, you’ve been an invaluable asset to us, both for your patience, your sup...

This page describes an easy workaround for the flashing error you get in Keil uVision when you are using nRF5 SDK v16 on nRF52833 chips.  The assumption is that you have installed the latest versions of nRF MDK and nRF-Command-Line-Too...

If you ask five different people “How would you define the Internet of Things?”, you will probably get five different answers! The term has generated a lot of buzz in the media in the past few years. You may see this as an unjustified hyp...

The nRF9160 SiP supports the use of both LTE-M and GPS. We want to show how these can be used in an application at the same time. In this project we demonstrate this by using the nRF9160 DK to send the GPS position of the DK to Google Cloud, which w...

This blog post contains answers to questions asked during the "Introduction to nRF Connect SDK" webinar hosted by Nordic Semiconductor 25.09.2019. You can watch a recording of the webinar here. You can download the slides at the b...