I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi,
I'm using pstorage, but found some problem. sd_flash_page_erase will not trigger system event after the operation is complete.
In my code, I registered the system...
Are you supposed to be able to nest critical regions using CRITICAL_REGION_ENTER and CRITICAL_REGION_EXIT? Here I mean you have a function which uses a critical region to...
I'm trying to run bootloader from nRF SDKv6 with SDv7 in gcc.
On our custom board, it runs, but does not advertise (sd_ble_gap_adv_start gets called and does not return...
Hi,
I have developed the firmware using nRF51822 Development Kit. I now want to get to put the firmware on nRF51822 chip used in breadboard. I got a smt adapter with nRF51822...
Hi!
When trying to update app using example bootloader for s110, v.7 from nRF Toolbox I get "Device is not supported. Check if it is in the DFU state".
Bootloader is...
Good morning,
In the application I'm developping with nRF51822 anb S110 SoftDevice, the final peripheral product will be installed in a physical non-accessible place. So...
Hello,
I'm working with the example ble_app_multilink_central of S120. In this example, the scan is done correctly in the three channels of advertising?
Thanks!
I have a characteristic which is a long string. I need to be able to read and write it.
Below is the function for writing to start with. Please comment on this function...
It appears version 7.0 of the SoftDevice 110 supports over the air flashing of softdevice/bootloader/application or a zip containing a combination of the three.
Trying...
Hi,
I'm trying to get SPI (master) to work (nRF51822) for communicating with a quadrature counter (LS7366R).
I've read several implementations of SPI master, such as the...
Using:
GCC 4.8
pure-gcc Setup
Sdk 5.2.0
Softdevice 6.0
I execute some code within interrupt context (softdevice handler) and also in main thread.
I need...
Hi,
What's the difference between a 0.9.0 pca10000 firmware and the earlier version (0.8.0)? I noticed that the throughput with 0.9.0 on the same dongle is much less than...
I'm trying to use the TWI master example with the S120 soft device. It looks like there is a known problem trying to get the S110 working with the hardware TWI. It seems the...
Hello.
I want to make flashing of devices for production faster.
So I want to write application together with bootloader via J-Link simultaneously and not via OTA DFU.
...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
