Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
Hi Nordic Team,
I would like to confirm whether enabling APPROTECT also implicitly enables Secure APPROTECT, or if these two protection mechanisms need to be configured...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
Hello, I am developing a system where I have a app and a Rigado BMD-300 Module. I am using, for experiment, the nRF Connect App and in program, I use SDK 14.2 and s132 softdevice...
Hi to everyone,
sorry if this question will result stupid, but I'm really new on programming Nordic microcontrollers.
I'm trying to develop a simple ble application for...
1. Did secure BLE DFU first time for hrs app, BL jump to hrs app
2. Did secure BLE DFU second time for hts app, BL jump to hts app
3. Did nrfjprog HID keyboard app and...
Hello,
I am using NRF52840 board and SDK 14.1, Softdevice 5.0.0-2.
I am testing other devices on my board. However, it seems to work normally until 2, but the connection...
Hi,
I just try the new mesh SDK V2.0.0. And I found that there is an error if I compile the "examples\light_switch\proxy_client" more than one time.
The error is here...
Hi,
I have successfully flashed nRF24LU1+ via ISP. Right now, I am validating using USB to download firmware for future production. Here is the issue.
Our project has...
Hello all,
I'm currently working on a project with a due date coming up soon. I'm using two (2) nRF24L01's with a nRF24L01+PA+LNA shield.
Right now I have my micro controller...
I want to change the advertising data of the advertising packets with time. I did find the solution for the same in this link - https://devzone.nordicsemi.com/f/nordic-q-a...
I have a board with an NRF52832 and an LED driver. I wrote a function that bit bangs a serial stream to an LED driver. It works when I use the nrf_gpio.h library.
However...
I am working with NRF 51DK. I am trying to flash a software on the target device which uses NRF51 microcontroller. I am using NrfGo studio. I am facing an error that, Unable...
Hi All,
I am newbie with nordic, and I need some help.
I am using nRF52832 with softdevice.
I need to generate a 128 kHz clock signal (PWM pulses with 128kHz frequency...
Hello, everyone!
I am a newbie developer about nrf51.
I need to advertise my BLE and save my power.
I have read the document that nrf51 has System-on (including some...
We have a couple of development units that are showing the above error in the nRF Toolbox app. Using the nRF Connect app, the DFU dialog just goes away and the screen reverts...
