We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I'm trying to make the basic Button sample work but am having problems.
The physical button is a latching button. Press it and it moves in with a click and physically stays...
nRF52832 Product Specification V1.4, page 344 lists predefined baud rates only.
Is it possible to use other values for custom baud rate, and if so, what is the relationship...
We have noticed an issue with received characters being dropped on the UART shell interface. Originally, we found the issue using our own application, but subsequently we...
I am using a nrf54l10 module on the pcb and using the nrf54l15 dev board. So I have a bootloader, the mcuboot, and then the image. I program over SWD on the pcb. So my problem...
Hello!
What would be the best way to start a custom LE Audio application with a different codec?
I mainly want to evaluate being able to stream 2-4 channels from a 53...
Hi,
I am using the npm2100 as a power management chip in my product, utilizing only the boost function. When only the npm2100 is soldered on the PCB with no load connected...
I am using nPM1300 MIKROE Click with ESP32 over I2C and enter ship mode by writing the required I2C registers from ESP32 .
Observed Behavior
Ship mode command is sent...
Hi,
I am developing a feature to add remote provisioning support to a BLE Mesh-based network. In the network, a provisioner node receives, via a serial command, the UUID...
Hello,
I am trying to reduce the current on the nRF5340 during the distance measurement (dm) sample for BLE ranging. For current measurement I am using the Power Profiler...
I've been trying to establish the network using Open Thread API.
After enabling the IPv6 by using otIp6IsEnabled , when try to start the joiner using otJoinerStart but it...
Hi,
I've already spent a lot of time on this issue. I develop on a Windows laptop. I need to run unit tests with Twister before committing to our repository. I can't do...
We are using SDK 3.1.1 and nrf52DK with our own Model ID and anti-spoofing key from Google.
When flashing the Locator Tag example to the board, a half sheet notification...
We are developing a battery-powered medical device using nRF9151 with nRF Connect SDK v2.9.0 , where data is transmitted to AWS IoT Core using MQTT over LTE Cat-M . While...
Hey, I'm looking for a solution to encypt the DFU_Application.zip and that the nrf52840 MCU can encrpyt it at runtime. Actually I've read that this not offical supported of...
I’m working on an indoor tracking system based on the Bluetooth LE Channel Sounding (CS) API. My target is to support multiple initiators connected to a single reflector,...
