Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
I am having a recurring problem with NFC-CONNECT: build action. It hangs when building. Gets stuck with the following message in lower-right hand corner of screen:
The...
I have successfully installed west and zephyr, and I have successfully build a simple tflite-micro hello_world example, but it just generates the zephyr.hex file. SInce i...
I am using a dynamic BAS service. I have noticed that after a few bt_gatt_service_unregister() and bt_gatt_service_register() calls, the following error occurs: bt_gatt: Unable...
Hi, trying to directly build the solution for the exercise i get this error at the end.
The whole log-output:
Building l5_e1_sol west build --build-dir /mnt/df01dc22-f3bf...
Hi! I am trying to get the samples "Bluetooth: Direction finding connectionless locator" and "Bluetooth: Direction finding connectionless beacon" to work on nRF54L15dk. I...
Cannot program our nRF9151-SMA-DK, we have other boards and work normaly. This is the programmer log:
08:30:21.996
Initialising the bundled nrfutil device
08...
nRF54L15 - ncs 3.02 - toolchain 3.02
I changed my build settings from no sysbuild to sysbuild in order to use serial recovery and/or FOTA. I thought everything was OK until...
Hi,
For my university MEng group project, I am working with the nRF5340 Audio DK and Bluetooth LE Audio (LC3 over ISO).
My end goal is to stream audio from an nRF5340...
hi,
i'm a beginner for nrf9160DK so can you guys help me to how can i nrf9160 up and running for the first time. i'm not able to up and running with this video https://www...
I have a problem where the GPIO pin is not working as intended (it is constantly high but it should be alternating high and low). Via debugging I've ascertained that the problem...
Hello, I am encountering a crash in MCUBoot when using the following configuration:
MCUBoot as bootloader (SB_CONFIG_BOOTLOADER_MCUBOOT)
TFM configuration (build /ns...
I am encountering a build error while setting up a build environment. Can you provide assistance as to what the issue I am encountering may be? I am using VSCode on MacOS...
hi,
i'm stuck at lesson 3 exercise 1 in step 1 so i create an application with choosing option 1 create a blank application for this first task to print hello world and...
Exhausted everything. Here's the guts of the code. A task is called at 2Hz to push the value, which at 1024/s makes an event time of +512. I set the cumulative RPM to +1 for...
Hello,
We have a nRF9160 product in production that is programmed with an image created by SDK 1.9.0 and with the default memory partition. We migrated to SDK 2.3.0 last...
