Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello All,
I implemented the HTTPS call to Amazon using the certificate, and the POST request returns the device ID. Like you docs: Exercise 2 - Adding TLS to the HTTP connection...
HI
My current system consists of an nRF54L15 paired with an external flash and sensor. In low-power mode, the current consumption is approximately 15 µA. After sleeping...
Hello! I am facing issues when trying to set up a PPP connection using the Serial LTE Modem (SLM) application on the nRF9151 DK, and I would appreciate some guidance. I am...
Hello,
I have seen many topics regarding the SAADC sampling modes and power consumption trade-offs on DevZone, but none of them clearly address my concerns. I would like...
Hi there,
We are currently developing a system, where around 480 kbytes of data are transmitted over BLE. Throughput is supposed to be as high as possible.
We are using...
I have a school assignment revolving a technological product, where i need to ask a few questions to a business about their involvement with the product. Therefore i need...
I set the voltage at the PPK “Source meter” to 1250mv, and then used a multimeter to measure the voltage between the PPK “vout” and “GND”, which was 2830mv. How can this situation...
Hi,
We're working on a cellular design using the nRF9151 with an nRF7000 for location finding. We have a working prototype on the Thingy91x and are currently focusing on...
I was reviewing the Large scale Bluetooth mesh testing - Blogs - Nordic Blog - Nordic DevZone and noticed the statement: " Initialize the network by flashing the test firmware...
I want to connect Waveshare E-ink display to nRF5340 using e-Paper Driver HAT. At first, I tried to make all the calls by my own, just by rewriting the code from the ESP driver...
I am attempting to use the COMP section to build a relaxation oscillator. There appear to be a number of interactions between sections, some of which are subtly documented...
Hi there,
I went through all the documentation and instructions in order to use my nRF52DK as a sniffer and I can not see it in the capture devices in wireshark.
am not...
1. What versions of GSMA specification does nrf9160-SICA modem support? In particular we are interesting in SGP.02, SGP.22 or SGP.32 versions.
https://www.gsma.com/esim...
We are developing a Bluetooth peripheral device.
The peripheral has no input/output capability, and a fixed passkey is pre-programmed.
We would like the pairing to succeed...
On the Online Power Profiler I noticed changing iDRX interval has a significant effect on power consumption. How can I adjust this interval on our device?
I saw this ticker...
