Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
After working with the path loss monitoring sample in NCS, I was wondering if there is a sample that accomplishes something similar to the following:
Central...
I'm programming a batch of 100 NRF52840 devices (new ISP1807-LR modules), and I'm unable to recover or program several of them. Most work fine, and I've never seen this issue...
I want to enable in nrf Connect SDK for nrf54L MCU FW image encryption for upgrade. In the project we use NSIB B0 bootloader plus MCUBoot with ability to upgrade MCUBoot and...
Hi,
I have a project requirement to interface with HART, which is a protocol that specifies odd parity for UART. I recently found out UART odd parity isn't supported on...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
I am trying to get the BMI270 working with a nrf5340 DK. I have read Unable to Connect nRF5340DK with BMI270 Over I2C - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
Hi Team,
I am trying BMI270 Sample using nRF54LM20 DK. But the problem here is it getting exited after checking the device is ready section.
Added my overlay file for...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
nrf sdk 2.9.2
I wanted to stop Bluetooth activity, so I used `bt_disable`, but a kernel panic occurred.
So I create a simple example to try this function, I still get...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Using the flash : https://datasheet4u.com/download_new.php?id=1588116 on SPI : XF_CS (P0.13), SCLK (P1.09) , SDI (P0.08) , SDO (P0.05) Flash specific parts in the nrf52840dk_nrf52840...
I have recently purchased nRF52840 dongle which I wanted to use as a ZigBee sniffer. I bought it on AliExpress and it supposed to be original Nordic board, but it turned out...
Hi everyone,
I’m trying to program/recover a custom board with an nRF52840 Fanstel module using a Nordic nRF52840 DK as the programmer. The board is powered from a 4.2 V...
Dear Nordic Support Team,
We are developing a Matter device based on the nRF54L15 using NCS 3.1.1 . We started from the Matter light example provided in the SDK.
We encountered...
